kromo premium 50 - User Manual

Questions and Answers

B
Brian JohnsonAug 8, 2025
How to remove streaks and spots from glasses and dishes in my kromo premium 50?
- J
  James KochAug 8, 2025
  Streaks and spots on glasses and dishes from your Kromo Dishwasher can be due to: * Too much rinse-aid. Reduce the rinse aid amount by turning the micrometric dispenser screw. * Water that is too hard. Check the water quality to ensure it doesn't exceed 10°f in hardness. * For appliances with a softener: too little salt or resins that haven't been properly regenerated. Fill the salt container with coarse salt (1-2 mm grains) and regenerate the resins more often. * Salt present in the dishwasher sump. Thoroughly clean and rinse the appliance, and avoid spilling salt when filling the container.
M
Ms. Carolyn FoxAug 14, 2025
Why aren't glasses and dishes drying properly in my kromo premium 50 Dishwasher?
- R
  Russell ClayAug 14, 2025
  If your glasses and dishes aren't drying properly in your Kromo Dishwasher, consider these factors: * Insufficient rinse aid. Increase the dosage by turning the dispenser screw. * Unsuitable rack. Use a suitable rack that provides an inclined position for the pots and tools, allowing water to rinse away. * Items sitting too long. Remove the rack with pots and tools as soon as the cycle stops to allow them to dry more quickly in the air. * Rinse temperature too low. Check the boiler thermostat temperature to ensure it's above 80°C. * Dish/glass surface. Replace dishes and glasses if their surface is too rough or porous. If the dirt is dry and old, soak before washing.
C
courtneymorganAug 19, 2025
What to do if my kromo premium 50 does not load water?
- P
  Pam PowellAug 20, 2025
  If your Kromo Dishwasher isn't loading water, check the following: * Ensure the water valve is open. * Inspect the rinse area nozzles or solenoid-valve filter for blockages or limestone scaling. Clean the rinse arm nozzles, piping, and solenoid-valve filter, and ensure the water hardness is less than 10°f. * A defective pressure-switch may be the cause. Replace the pressure-switch.
O
ojonesAug 27, 2025
Why does my Kromo Dishwasher stop during the wash stage and start refilling water?
- T
  tuckergaryAug 27, 2025
  Your Kromo Dishwasher might stop during the wash stage and start refilling water if: * The previous day's water was not changed. Drain the tank completely and refill it. * There is excessive water temperature in the tank. * There is a defective pressure switch.
Z
Zachary HarperNov 1, 2025
Why are the washing results unsatisfactory with my kromo premium 50?
- R
  Richard MaynardNov 1, 2025
  Unsatisfactory washing results with your Kromo Dishwasher can occur for several reasons: * The washing nozzles may be obstructed, or the rack may not rotate. Ensure you carefully clean the nozzles and check the wash-arm's positioning, tightening it firmly. * Foam might be present. Use no-foam detergents or reduce the detergent dose. Also, check the rinse-aid dosage. * Fats or starches may not be removed due to insufficient detergent concentration. * The filters may be dirty. Remove the filters, clean them with a brush under running water, and replace them in their original position. * The tank temperature may be incorrect (it should be between 50°C and 60°C). Adjust the thermostat or check the heating element's operation. * The wash cycle may be too short for the level of dir...

Summary

General Safety Warnings

Machine Description

Machine Overview and Standard Equipment

Physical components, standard racks, baskets, and accessories for 40mm and 50mm configurations.

Technical Features and Specifications

Key operational features, connections, noise level, and essential technical data of the unit.

Machine Operation

Control Panel, Startup, and Wash Cycles

Explanation of controls, startup steps, running wash cycles, and selecting programs.

Shutdown, Consumables, and Drainage

Procedures for machine shutdown, using detergent/rinse aid, and managing the drain pump system.

Optional Water Softener Function

Details on the optional water softener, its regeneration cycle, and salt usage.

Usage Safety and Compliance

Critical Usage Safety Warnings

Essential safety warnings and rules for operating the appliance to prevent accidents and damage.

Environmental Recommendations and Hygiene

Advice on resource optimization and adherence to HACCP/hygiene regulations.

Maintenance Procedures

Routine Daily Maintenance

Daily cleaning tasks including filters, arms, nozzles, and tank care for optimal performance.

Extraordinary Maintenance and Checks

Periodic inspections and servicing by qualified technicians for machine longevity and safety.

Installation Guide

Pre-Installation Preparation

Guidelines for handling, storage, and preparing the installation environment, including room features.

Connection Requirements

Specifications for water supply, electrical connections, and steam evacuation, including pressure and hardness limits.

Final Installation and Initial Startup

Steps for machine positioning, leveling, wiring, water connection, and initial startup after professional installation.

Troubleshooting and Alarms

Signals and Alarm Messages

Explanation of various error signals and alarm messages displayed by the machine, with their causes and remedies.

Common Problem Resolution

A guide to identifying and resolving common issues with the machine's operation and performance.

Environmental Aspects and Disposal

Packaging Disposal Procedures

Instructions for disposing of packaging materials in accordance with local laws and regulations.

Product and WEEE Disposal

Procedures for the proper disposal of the machine and its components as electronic waste (WEEE/RAEE).

kromo premium 50 Specifications

General

Brand	kromo
Model	premium 50
Category	Dishwasher
Language	English

Related product manuals