Krone Swadro 42 T - User Manual

O r i g i n a l o p e r a t i n g i n s t r u c t i o n s
Rotary Swather
<v>T - Typ1</v> Swadro 38 T </v>
<v>T - Typ2</v> Swadro 42 T </v>
<v>T - Typ3</v> Swadro 46 T </v>
<v>T - Typ4</v> </v>
<v>T - Typ5</v> </v>
<v>T - Typ6</v> </v>
<v>T - Typ7</v> </v>
<v>T - Typ8</v> </v>
<v>T - Typ9</v> </v>
<v>T - Typ10</v> </v>
( <v>T - ab Masch.-Nr.</v> from serial no. </v> : 770 633)
<v>T - Bestell-Nr.</v> Order no. </v> : 150 000 025 01 us
<v>B - Titelbild</v> </v>
03.05.2010

Krone Swadro 42 T Specifications

General

Working Width	4.2 m
Transport Width	2.5 m
Number of Tine Arms per Rotor	11
Tines per Arm	4
Required Hydraulic Connections	1 x single-acting

Summary

4 Safety and Hazard Prevention

4.2 Safety Sticker Placement

Illustrates the locations of various safety stickers on the machine.

4.4 Symbols in Operating Instructions

Explains the meaning of symbols used in the manual for safety instructions.

4.5 Hazard Warning Symbols

Defines the 'Danger', 'Warning', and 'Caution' symbols and their effects.

4.5.1 Personnel Qualification and Training

Specifies requirements for operators, maintenance, and repair personnel.

4.5.2 Dangers of Non-Compliance

Outlines risks and consequences of not following safety instructions.

4.5.3 Safety-Conscious Work Practices

Details essential safety practices for daily operation and maintenance.

4.6 Safety and Accident Prevention Regulations

Lists general safety rules and accident prevention regulations.

4.8 PTO Operation Safety

Safety guidelines for operating the Power Take-Off (PTO) shaft.

4.9 Hydraulic System Safety

Safety instructions for connecting and working with the hydraulic system.

4.11 Safety During Maintenance

General safety rules to follow during maintenance activities.

4.12 Unauthorized Conversion and Spare Parts

Warnings against unauthorized modifications and the use of non-original parts.

4.13 Inadmissible Operating Modes

4.14 Machine Safety Instructions

5 Commissioning the Rotary Swather

5.4 PTO Shaft Installation and Length Adjustment

Covers PTO shaft installation and the crucial length adjustment procedure.

6 Start-up Procedures

6.4 Hydraulic Connections and Safety

6.5 PTO Shaft Installation

Step-by-step guide for installing the PTO shaft.

7 Driving and Transport Procedures

7.1 Preparation for Transport

8 Machine Operation

8.2 Transport to Working Position

Instructions for converting the machine from transport to working configuration.

8.4 Swath Former Adjustment

8.5 Raking Height Adjustment

8.6 Travelling and Drive Speed

8.7 Switching to Transport Position

Steps to convert the machine from working to transport mode.

10 Maintenance and Servicing

10.1 Maintenance Safety Instructions

General safety rules to follow during maintenance tasks.

10.2 Using Genuine Spare Parts

10.7 Replacing Tine Arms

11 Lubrication Chart

11.1 Lubrication Safety Instructions

General safety rules to follow during lubrication tasks.

11.2 PTO Shaft Lubrication

11.3 Machine Lubrication Chart

12 Gearbox Maintenance

13 Maintenance - Hydraulic System

13.1 Hydraulic System Maintenance

Covers maintenance procedures and safety for the hydraulic system.

15 Placing the Machine in Storage

15.1 Storage Safety Instructions

General safety rules to observe when preparing the machine for storage.

15.2 End of Harvest Season Preparation

15.3 Before Start of New Season Checks

15.4 Pre-Season Safety Instructions

Safety guidelines before starting operation after storage.

16 Malfunctions, Causes, and Remedies

16.1 Safety for Troubleshooting

General safety rules to follow when troubleshooting malfunctions.