76
ENGLISH
MAINTAINING YOUR APPLIANCE
little washing up liquid and a small non-abrasive brush. Rinse and dry it - Fig. 14. Before
putting it back, ensure that the air inlet holes are not blocked by any milk residues. If
necessary, unblock them using the needle supplied - Fig. 15.
Do not wash the steam nozzle in a dishwasher.
To interrupt the steam function, simply press any button.
If the nozzle is obstructed, unblock it with the needle provided.
Steam can be produced for a maximum of 2 minutes per cycle.
After the steam function has been used, the nozzle can be hot, and we recommend
that you wait for a few moments before handling it.
Auto-cappuccino XS 6000 Set (sold separately)
This auto-cappuccino accessory enables you to make cappuccinos or lattes - Fig. 16.
Connect the different parts to each other. Ensure that you do not pierce the pipe by keeping
the button in the correct place.
After removing the lid, ll the jug with milk - Fig. 17 and place a cup or glass under the
auto-cappuccino nozzle - Fig. 18. Select the cappuccino or latte position on the special
nozzle - Fig. 19.
Start the steam, as indicated in the chapter ‘Making drinks with steam’.
Once you have made the milk froth, place your cup under the coffee outlets and start a
coffee cycle - Fig. 20.
To prevent the milk from drying on the auto-cappuccino accessory, ensure that you clean
it thoroughly. You are advised to wash it immediately by running a steam cycle with the
accessory jug lled with water in order to clean the inside of the nozzle. You can use the
KRUPS liquid cleaner for this, available separately.
Emptying the coffee grounds collector and the drip tray.
If the light ashes,
Remove, empty and clean the coffee ground collector - Fig. 21.
Remove, empty and clean the drip tray - Fig. 23.
The drip tray is equipped with oats to indicate when it needs to be emptied.
Put all parts back in place.
As soon as you remove the coffee grounds collector, you will have to empty it completely
to avoid any overow.
The light will remain on if the used grounds collector is not pushed firmly into
place or is incorrectly installed.
You cannot make espresso or coffee while the light is on or is ashing. The coffee
grounds collector has a capacity of 9 coffees.
Rinsing of circuits
These 2 functions are available anytime, except if the appliance requests a ‘CLEAN’
and/or ‘CALC’ cycle.
Rinsing out the coffee circuit:
Place a container under the coffee nozzles. Press the button - Fig. 6 quickly to start a
coffee circuit rinsing cycle, which will automatically stop after around 40 ml.
Rinsing out the steam circuit:
Place a container under the steam nozzle and press the button for 3 seconds to start a
steam circuit rinsing cycle, which will automatically stop after around 300 ml.
Appliance cleaning program, 3 times a year (total duration:
about 13 minutes)
For hygienic reasons and to preserve all best coffee avor we recommend you to clean the
coffee system when the machine asks you to, about 3 times a year.
To perform this cleaning you will need:
– 1 KRUPS cleaning tablet
– 1 container of minimum 600ml
several ows will follow one another
When to carry out this program?
When it is necessary to run a cleaning program, the appliance alerts you by ashing the
CLEAN indicator light. This program can only be accessed when the appliance requests it
(approximately every 300 brews of coffee or espresso).
To comply with the warranty conditions, it is essential to perform the cleaning cycle when
the appliance alerts you. Follow the order of operations carefully
Use only KRUPS cleaning tablets (available on our KRUPS.com store)
How to start the automatic cleaning program?
1. Start the cleaning program by pressing the button
. The CLEAN indicator becomes
solid and the and indicators ash.
2. Remove, empty, clean and replace the coffee grounds collector Fig 21-22 The indicator
light
go off
3. Remove, empty, clean and replace the drip tray Fig 23
4. Fill and replace the water tank.
5. Place the 600 ml container under the coffee nozzles Fig 24
6. Open the maintenance hatch Fig 25
7. Insert the KRUPS XS3000 cleaning tablet into the cleaning chute Fig 26
8. Press the button
to start the cleaning cycle
9. The cleaning phase (about 13 min) starts. Several water ows follow one another in
several phases without any necessary intervention. They allow the device to be rinsed
and the cleaning residue to be removed.
10. The cleaning cycle is nished when the light
stays on and the CLEAN light goes out,
empty the drip tray.
Your device is ready to be used.
Important:
You do not have to run the cleaning program as soon as the appliance requests it, but you
must do it reasonably soon after. If cleaning is postponed, the alert message will remain
displayed as long as the operation has not been performed.
if you unplug your machine or if you turn it off during cleaning or in the event of electrical
failure, the cleaning program will resume the current step at the time of the incident. It will
not be possible to postpone this operation: rinsing the water circuit is mandatory.
If there is not enough water in the water tank when you start the program, the light
will come on to warn you. Add the appropriate amount of water to the container and
cleaning will continue automatically.
To Next Page
Loading...
Need help?
General
