KUGELHAHN MÜLLER GMBH
Subsidiary of Bray International, Inc.
Kölner Str. 686 · D-47807 Krefeld
T: +49 2151 30 80 41
·
F: +49 2151 30 80 39
info@kh-m.de
·
www.kugelhahn-mueller.de
Management
Craig C. Brown
George Crooks
Register court
District court Krefeld
·
HRB 1747
VAT-ID-No.: DE 811 302 631
National Bank AG Duisburg
SWIFT-BIC: NBAG DE 3 E
IBAN:
DE20 3602 0030 0005 0039 11
DECLARATION OF CONFORMITY AS PER DIRECTIVE 2014/68/EC AND
MANUFACTURER'S DECLARATION AS PER DIRECTIVE 2006/42/EC
The manufacturer Kugelhahn Müller GmbH, D-47807 Krefeld, Kölner Straße 686, declares that the valves:
Flanged ball valves with Teflon® and O-ring seal at the shaft of Series KM-O and KM-T
> with lever or gear with handwheel
> with pneumatic, electric or hydraulic actuator
> with bare shaft for subsequent actuator assembly
comply with the directives mentioned below as follows:
Pressure Equipment Directive 2014/68/EC (PED): [only if Art. 3 Clause 1.3 or Art. 3 Clause 3 applies]:
The valves are conform with this directive. The conformity assessment procedure applied as per Annex III of the Pressure Equipment Directive 2014/68/EC is for
category I to III, module H1. - Category IV does not apply to isolation valves.
The valves can be used for various fluids within the permissible pressure and temperature limits, taking the respective influences on the pressure equipment into
consideration. Use in fluid group 1 and 2 is permitted.
The fluid resistance of the valve incl. the components shall be checked for the operating conditions prior to use.
Machinery Directive 2006/42 EC (MD) [applies only if the valve is operated other than by hand]:
The vale is an "incomplete machine" within the meaning of Art. 1 and is intended for installation in a pipe system as complete machine. The listing of conformity with
the clauses of the Machine Directive as per page 2 and 3 of this declaration and the provided (original installation instructions OM-KM-OST/TST) shall be observed by
the planner / user.
In relation to the directives above, the following applies:
1. The user shall follow the "intended use" as defined in the above instructions (OM-KM-OST/TST) included with the delivery and observe all safety-relevant notes in
these instructions. Disregard of these instructions can release manufacturer from his product liability.
2. The commissioning of the valve (and, where applicable, of the attached actuator) is not permitted until the conformity of the system into which the valve is
installed, with all relevant European Directives, is declared by the person responsible and risk of injury is thus ruled out.
The manufacturer Kugelhahn Müller GmbH has performed and documented all necessary risk analyses. For the carbon steel used, a corrosion allowance is neither
required nor taken into account for the calculation.
Standards and rules applied:
DIN EN 12516, AD2000 regulations, DIN EN ISO 9001, DIN EN ISO 12100:2009, DIN EN ISO 5211, DIN EN 1983, DIN EN 12266
Type description
KM-OXST-F1/F27
KM-OX-F1/F27
KM-OAST-F1/F27
KM-OA-F1/F27
KM-TXST-F1/F27
KM-TX-F1/F27
KM-TAST-F1/F27
KM-TA-F1/F27
Dimension sheets no special tools required for replacement of wear parts
MB 015-065-KM-OST.00,
MB 080-200-KM-OST.00,
MB 015-065-KM-O.00,
MB 080-100-KM-O.00,
MB 015-065-KM-TST.00,
MB 080-200-KM-TST.00,
MB 015-065-KM-T.00,
MB 080-100-KM-T.00,
Conformity assessment procedures applied:
according to Annex III of Pressure Equipment Directive 2014/68/EC; Module
H1
Changes to ball valves and/or components that impact the technical data
of the ball valve, the (intended use) as per section 1 of these instructions
and significantly modify the valve or a provided component make this
declaration null and void.
Name of notified body:
TÜV Rheinland Industrie Service GmbH Am Grauen Stein, 51105 Köln
ID-number of notified body:
0035
Signature:
Name: George Crooks
Position: Managing Director
Date: 23 March 2018
To Next Page
Loading...
Need help?
General