Why is the oil heating up in my KUHN Farm Equipment?
If the oil is heating up in your KUHN Farm Equipment, check the settings of the valve block and adjust if required. Also, reduce the hydraulic oil flow at the tractor.
What to do if I get a connection error on my KUHN SW1604?
If you're getting a connection error on your KUHN Farm Equipment, begin by inspecting the cables between the control panel and the control box for any damage or loose connections. Also, check the fuse. If the issue persists, try disconnecting the power supply for 15 seconds and then reconnecting it. If the error continues, it might indicate a more complex software or internal problem.
What to do if I get a rotation/unload position sensor error on KUHN SW1604 Farm Equipment?
If you're experiencing a rotation/unload position sensor error (time-out) on your KUHN Farm Equipment, start by checking if the wrapping table is blocked by any items. If the table is clear, ensure that the hydraulics are switched on and check the hydraulic system and all hydraulic hoses for leakage and correct connection. Also, verify that the oil flow from the tractor is sufficient. Finally, make sure that the table rotation/unload position sensor is correctly positioned and check the sensor and the sensor cable routing.
What to do if the table is not in bale load position on KUHN SW1604 Farm Equipment?
If the table is not in the bale load position on your KUHN Farm Equipment, start by checking if the wrapping table is blocked. If not, verify that the hydraulics are switched on and check the hydraulic system and all hydraulic hoses for leakage and correct connection. Ensure that the oil flow from the tractor is adequate. Also, check that the table load position sensor is correctly positioned and inspect the sensor and the sensor cable routing.
What to do if the table is not in bale unloading position on KUHN SW1604?
If the table is not in bale unloading position on your KUHN Farm Equipment, check for any obstructions blocking the wrapping table. Ensure the hydraulics are powered on and inspect the hydraulic system and hoses for leaks and proper connections. Also, verify the position of the table rotation/unload position sensor and check the sensor and the sensor cable routing.
Why does the film tear at the lower edge on KUHN SW1604?
If the film tears at the lower edge on your KUHN Farm Equipment, the pre-stretcher may be set too low. Adjust the pre-stretcher height to resolve this.
Why are there holes in the stretched film on my KUHN Farm Equipment?
If you notice holes in the stretched film on your KUHN Farm Equipment, the pre-stretcher rollers might be dirty. Clean the pre-stretcher rollers to resolve this issue.
What causes the film to slip along the bale edge on KUHN SW1604 Farm Equipment?
If the film slips along the edge of the bale on your KUHN Farm Equipment, the pre-stretcher might be set too high. Adjust the pre-stretcher height to correct this.
What does a voltage error mean on my KUHN Farm Equipment?
If you're getting a voltage error on your KUHN Farm Equipment, it might be due to low tractor battery voltage. Try switching off all heavy electric power consuming devices and restart the process. If the error persists, switch off all electric devices, turn off the engine, wait a moment, and then restart the engine before proceeding.
What to do if the loading arm is not detected in lowest position on KUHN SW1604 Farm Equipment?
If the loading arm is not detected in the lowest position on your KUHN Farm Equipment, first ensure that the loading arm is actually in the lowest position. Next, verify the position of the loading arm down sensor and inspect the sensor and its cable routing.
Manual for trained farmers/individuals; dealer provides training on operation and care.
Explains symbols and pictographs used in the manual for better comprehension.
Emphasizes following safety instructions for accident avoidance and machine safety.
Explains safety decals indicating dangers and their maintenance.
Defines who can operate/service the machine and general safety duties.
Safety precautions and procedures for hitching the machine to the tractor.
Safety for hydraulic couplings, pressure, and leak checks.
Installation of cable control lever unit and electronic connections.
Checking and setting hydraulic block for tractor system compatibility.
Complying with Road Traffic Act for safe transportation.
Steps to empty and position table/arm/wheels for transport.
Final check to ensure all conditions are met for road transport.
Safety rules and initial preparations before operating.
Adjusting table rollers, support rollers, and pre-stretcher.
Safety steps and procedures for loading film rolls.
Key safety points during machine operation.
Detailed steps for bale wrapping using cable or electronic control.
Overview of cable, electronic, and remote control systems.
Adjusting parameters for wrapping, counters, and system functions.
Safety rules and general cleaning steps for the machine.
Cleaning pre-stretcher rollers and post-cleaning lubrication.
Safety during storage and steps for unhitching the machine.
Tasks to perform when storing the machine long-term.
Safety, genuine parts, and general maintenance guidelines.
Tightening schedules and torque values for bolts.
Maintenance for pre-stretcher rollers and gears.
Maintenance for film cutter cylinder, knife, and sliding tube.
Safety, hoses, and oil filter maintenance.
Maintenance for drive chains.
Checks for axles, wheels, tyres, and bearings.
Cleaning and checking sensors.
Ordering parts, genuine accessories, and mounting guidelines.
Details on film break set, gear kits, remote control, etc.
Safety precautions before resolving problems.
Understanding error codes and continuing after resolution.
Common problems like film issues, loading arm, hydraulics.
Adjusting table lock, film cutter knife, sensors.
General| Bale weight | up to 1200 kg |
|---|---|
| Wrapping table | Yes |
| Film width | 750 mm |
| Transport Width | 2.50 m |
| Bale diameter | 1.6 m |
To Next Page
