Why is my Kumio ICM1232 making ice that's too large and sticking together?
If your Kumio Ice Maker is producing ice that is too large and sticking together, it's likely due to ice from previous cycles remaining in the water tray. To solve this, take out the ice while the machine is in standby mode.
What to do if all indicators twinkle simultaneously on my Kumio ICM1232 Ice Maker?
If all the indicators on your Kumio Ice Maker are twinkling simultaneously, it could be due to a few reasons: the water tray might be blocked by an ice cube, the motor could be stuck, fallen off, or damaged, or the micro switch might be broken. To resolve this, unplug the power, remove any ice blocking the tray, then plug the power back in and press the ON/OFF button. The machine will restart after 3 minutes.
What to do if the water shortage indicator light is on in my Kumio ICM1232 Ice Maker?
If the water shortage indicator light is on in your Kumio Ice Maker, it means either there is no water or the pump is full of air. To fix this, first add water until it reaches the MAX position. Then, press the ON/OFF button to restart the ice maker.
Why does my Kumio Ice Maker not display the ICE FULL icon when it's full?
If your Kumio Ice Maker doesn't display the ICE FULL icon when it's full, it could be due to a damaged ice full sensor or sunlight interference. Try replacing the ice full sensor or making ice indoors.
What to do if my Kumio ICM1232 has been working, but the water has been warming?
If your Kumio Ice Maker has been running, but the water has been warming up, the solenoid valve may have broken down. The suggested solution is to replace the solenoid valve.
How to troubleshoot a Kumio Ice Maker compressor that is making a buzzing noise?
If the compressor in your Kumio Ice Maker is working abnormally and making a buzzing noise, it could be that the voltage is lower than recommended. Stop the ice maker and do not restart it until the voltage is normal.
What to do if the indicator lights on my Kumio ICM1232 Ice Maker display are not on?
If the indicator lights on your Kumio Ice Maker display are not on, it could be due to a blown fuse or no power. Replace the fuse or turn the power on.
Includes instructions for unpacking, initial positioning, voltage compliance, and handling the power cord.
Covers electrical shock protection, ventilation, accessory use, and operating conditions.
Details what not to do, like using outdoors, using abrasive cleaners, or storing flammable substances.
Specifies suitable environments and warnings regarding cord placement and disposal.
Addresses child supervision, appliance disposal, and flammable refrigerant warnings.
Highlights quick ice making, indicator prompts, ice type, and cleaning function.
Safety advice for moving the unit, checking components, ensuring level surface, and initial setup.
Ensures voltage compatibility and recommends mineral water over distilled.
Explains the function of ON/OFF, Clean buttons and ICE FULL, ADD WATER, ICE MAKING indicators.
Details the process for starting the machine, deicing, ice making, and using the cleaning function.
Instructions for opening the lid, removing the basket, and filling the water reservoir.
Guide on plugging in, starting the machine, and handling initial ice production.
Advises on choosing small or big ice based on indoor temperature.
Notes that initial ice cycles produce small and irregular ice.
Instructs to remove ice immediately when the basket is full to prevent overflow.
Details cleaning of internal components using a water and vinegar solution.
Ensures ventilation openings are clear and advises against mechanical defrosting aids.
Covers restarting after idling, changing water, and compressor restart delays.
Emphasizes using fresh water for optimal ice production.
Addresses ice chip jamming in the shovel after a power loss or button push.
Troubleshooting steps for when the ice shovel cannot move ice to the basket.
Diagnoses abnormal compressor noise potentially linked to low voltage.
Solutions for water shortage indicators and non-functioning display lights.
Addresses problems like large ice pieces and no ice production.
Troubleshoots simultaneous indicator twinkling and warming machine.
Solutions for when the ICE FULL icon does not display correctly.
Mandates replacement of damaged power cords by qualified personnel.
Specifies using potable water and explains 'cloudy' ice formation.
Informs users that compressor and condenser surfaces can become very hot.
Reiterates limitations for persons with reduced capabilities and child supervision needs.
Provides instructions for responsible disposal and recycling of the appliance.
This document is an instruction manual for the Kumio ICM1232 Ice Maker.
The Kumio ICM1232 is an ice maker designed for household and similar applications. Its primary function is to produce bullet-shaped ice cubes quickly and efficiently. The device features a cleaning function for easy maintenance and provides prompts when the ice basket is full or when the water reservoir is insufficient. It is suitable for use in various environments such as staff kitchen areas, farmhouses, hotels, motels, bed and breakfast establishments, and catering services.
The ice maker is designed for user-friendly operation with a control panel that includes an ON/OFF switch button and a Clean function button. Indicator lights provide visual cues for "ICE FULL" (ice full alarm), "ADD WATER" (water shortage alarm), and "ICE MAKING" (ice making status).
Initial Setup:
Operation Steps:
Ice Production Notes:
Safety Precautions:
Cleaning:
Troubleshooting:
Disposal: This product should not be disposed of with other household waste in the EU. It should be recycled responsibly through return and collection systems or by contacting the retailer to promote sustainable reuse of material resources and ensure environmentally safe recycling.
To Next Page
General
