EasyManuals Logo

Kurzweil K2000 User Manual

Kurzweil K2000
133 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #43 background imageLoading...
Page #43 background image
Section
3
KURZASSM.OOC
12122192
3.2.5
3.2.5.1
3.2.6
3.2.6.1
3.2.6.2
3.2.6.3
3.2.6.4
3.2.6.5
3.2.7
3.2.7.1
3.2.7.2
3.2.7.3
3.2.7.4
3.2.8
3.2.8.1
3.2.8.2
3.2.8.3
3.2.8.4
3.2.8.5
3.2.9
3.2.9.1
3.2.9.2
AUD/PWR
BOARD
REMOVAL
Removal
of
this
board
is
the
same
as
3.2.4.1
above
except
there
are
ten
(10)
machine
screws
securing
the
connector
panel
to
the
metal
chassis.
SLIDER
BOARD
REMOVAL
Before
removing
bottom
of
shell,
remove
slider
knobs.
Remove
bottom
of
shell
as
per
3.1.2
above.
Remove
ENGINE - AUD/PWR
unit
as
per
3.2.2
above.
Using
figure
1
for
reference,
locate
the
slider
board
between
the
Front
panel
and
disk
drive.
Remove
the
single
self-tapping
screw
and
the
board
is
free.
Reverse
3.2.6.4
for
reassembly.
LCD
REMOVAL
Remove
bottom
of
shell
as
per
3.1.2
above.
Remove
ENGINE - AUD/PWR
unit
as
per
3.2.2
above.
The
LCD
board
is
surrounded
by
the
Front
Panel
board.
Remove
the
four
(4)
self-tapping
screws
securing
the
LCD
and
lift
the
board
free.
Reverse
3.2.7.3
to
reinstall.
FRONT
PANEL
REMOVAL
Before
removing
the
bottom
half
of
the
shell,
remove
the
round
knob
on
the
Front
Panel.
Also
removing
the
retaining
nut
and
washer
under
this
knob.
Remove
bottom
of
shell
as
per
3.1.2
above.
Remove
ENGINE - AUD/PWR
unit
as
per
3.2.2
above.
Remove
the
nine
(9)
self-tapping
screws
securing
the
Front
Panel
and
carefully
lift
panel
from
instrument.
NOTE:
This
board
can
be
easily
damaged
by
careless
handling.
BE
CERTAIN
TO
USE
CAUTION
WHEN
HANDLING
THIS
BOARD.
Reverse
3.2.8.4
above
to
reinstall
the
Front
Panel
board.
Be
certain
to
remember
to
use
the
ninth
screw
to
secure
the
bracket
(used
for
clamping
the
cables)
in
the
center
front
of
the
panel.
POWER
TRANSFORMER
AND
POWER
RECEPTACLE
REMOVAL
Remove
bottom
of
shell
as
per
3.1.2
above.
Note
that
the
Power
Transformer
and
Power
Receptacle
are
hard-
wired
as
a
unit.
The
harness
from
the
secondaries
of
the
transformer
are
routed
to
J20
on
the
AUD/PWR
board;
thus,
can
be
easily
removed
from
the
instrument.
3

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Kurzweil K2000 and is the answer not in the manual?

Kurzweil K2000 Specifications

General IconGeneral
TypeDigital Synthesizer
Polyphony24 voices
Weight35 lbs
Year Released1991
WaveformsSample-based, user loadable
LFOYes
FilterYes, multimode
EffectsYes, multi-effects processor
Keyboard61 keys
Memoryexpandable RAM
StorageFloppy disk drive
MIDIYes
OutputsStereo
DisplayLCD
Timbrality16-part multitimbral

Related product manuals