To test the expansion memory, proceed as follows: 1. Make sure the power switch is off. Plug the power cord into the printer and turn power on.
2. When the printer is on-line, press the STATUS key. 3. If the installation has been successful, the amount of memory shown on the status page will
correspond with the amount of expanded memory. (The factory installed memory size is 8 MB for the FS-1750 and 16 MB for the FS-3750.
) 1-26 2.1. Control Panel Chapter 2 Operating the Laser Printer This chapter explains the printer's control panel and operating procedures. It covers the
fundamental information you will need to use the page printer. 2.
1. Control Panel The printer control panel comprises a message display, keys, and indicators, as shown below. Symbolic Indicators ( Page 2-4) ( Page 2-5)
FORM FEED/ STACK/+ Key Message Display ( Page 2-2) CONTINUE/ ON LINE Key Key Key Copy Indicator Paper Size Indicator Resolution Indicator
Interface Indicator ( Page 2-2, 3) CANCEL Key - /FEED Key EXIT/MODE Key ENTER/STATUS key ( Page 2-5) 2-1 2.1. Control Panel Message Display The
message display gives information in the form of short messages. The six messages listed below are displayed during normal warm-up and printing. Message
6HOIý WHVW 3OHDVHý ZDLW 5HDG\ 3URFHVVLQJ :DLWLQJ 6OHHSLQJ Meaning The printer is self-testing after power-up. The printer is warming
up and is not ready. The printer is ready to print. The printer is receiving data, generating graphics, reading an memory card, or printing.
The printer is waiting for a command that says the job is over before printing the last page. Pressing the FORM FEED key allows you to obtain the last page
immediately. The printer is in Sleep mode. The printer wakes from Sleep mode whenever a key on the control panel is pressed, the cover is opened or closed,
or data is received. The printer then warms up and goes online. (The time that it takes the printer to enter Sleep mode depends on the Sleep Timer setting.)
Data inside the printer is being canceled. The printer prints the last page after a waiting period. &DQFHOOLQJý GDWD )RUP)HHGý 7LPHý 2XW Other
messages appear when the printer needs the operator's attention as explained in Chapter 5. Interface Indicator The interface indicator shows which of the
printer's interfaces is currently active.
It uses the following abbreviations: 3$5 6(5 237 Standard bi-directional parallel interface Serial interface (RS-232C/RS-422A) Optional interface
Theý3$5,ý6(5, orý237 indicator flashes when the printer is receiving and has received all the data, and then remains on. Resolution Indicator This shows the
current printing resolution. The resolutions below can be switched on the control panel. The default is 1200 dpi (Fast 1200 mode) in the PCL 6 and KPDL
emulation mode and 300 dpi in other emulation modes. The printer's resolution can be selected using the printer's control panel (See the last page in this
manual.
). For 1200 dpi, there are two modes, Fast 1200 mode and Fine 1200 mode. See Mode Select Menu at the end of this manual. êíí çíí ìëííó ìëíí Print Print Print
Print at at at at 300 dpi. 600 dpi.
1200 dpi (Fast 1200 mode) (Default). 1200 dpi (Fine 1200 mode). 2-2 2.1. Control Panel Paper Size Indicator This is the paper SIZE indicator which
indicates: Ì the size of the current paper cassette (letter size for the U.S.A. and A4 for European countries). The following abbreviations are used to indicate
the paper sizes. $é $è $ç %è %ç /7 /* 02 %8 * ** ISO A4 (21 cm × 29.
7 cm) ISO A5 (14.8 cm × 21 cm) ISO A6 (10.5 cm × 14.8 cm)** JIS B5 (18.2 cm × 25.6 cm) JIS B6 (12.8 cm × 18.2 cm) Letter (8-1/2 × 11 inches) Legal
(8-1/2 × 14 inches) Monarch (3-7/8 × 7-1/2 inches)* Business (4-1/8 inches) * ** '/ &è Eè (; úç úä +$ 2+ &8 ISO DL (11 × 22 cm)* ISO C5 (16.2 × 22.9
cm)* ISO B5 (17.
6 × 25 cm)** Executive (7-1/4 × 10-1/2 inches)** Commercial 6-3/4 (3-5/8 × 6-1/2 inches)* Commercial 9 (3-7/8 × 8-7/8 inches)* Japanese Postcard (10 ×
14.
You're reading an excerpt. Click here to read official KYOCERA
FS-1750 user guide
http://somemanuals.com/dref/324820
To Next Page
Loading...
