Why does my Kyocera FS-1370DN print completely blank pages?
If your Kyocera Printer produces completely blank printouts, open the front cover and check that the toner container is correctly installed in the printer.
Kyocera FS-1370DN Printer not turning on, what to do?
If nothing lights up on the operation panel of your Kyocera Printer, even when it's turned on, ensure the power cord is properly plugged into the power outlet. Connect both ends of the power cord securely, and try replacing the power cord. Also, check the power switch is in the On (|) position.
How to fix poor print quality on Kyocera FS-1370DN?
To address poor print quality on your Kyocera Printer, try selecting half speed mode using the printer driver.
How to fix vertical streaks on Kyocera FS-1370DN?
If your Kyocera Printer is producing vertical streaks, replace the toner container if necessary and clean the charger wire. Also, check the charger cleaner of the drum unit is in its original position.
How to resolve gray background on Kyocera FS-1370DN Printer prints?
To resolve gray background issues with your Kyocera Printer, replace the toner container if necessary, and check that the developer unit and drum unit are installed correctly.
How to clean dirt from Kyocera FS-1370DN Printer paper?
To address dirt on the top edge or back of the paper from your Kyocera Printer, clean the registration roller.
What to do if Kyocera FS-1370DN Printer prints status page but not computer data?
If your Kyocera Printer prints a status page but not data from your computer, check the program files and application software. Try printing another file or using another print command. If the issue persists with a specific file or application, verify the printer settings for that application. Also, ensure both ends of the interface cable are securely connected and consider replacing the printer cable.
Why is vapor emitted from my Kyocera FS-1370DN Printer?
If you notice vapor emitting near the top tray of your Kyocera Printer, it might be due to low temperature near the printer or humidity in the paper. The heat generated during printing can evaporate water moisture. To resolve this, increase the room temperature and use paper stored in a dry place. Printing can be continued without any problem.
Why is my Kyocera FS-1370DN printing faint or blurred?
If your Kyocera Printer is printing faint or blurred images, replace the toner container if necessary and clean the charger wire.
Why is my Kyocera Printer printing incomplete or out of position?
If your Kyocera Printer output is incomplete or out of position, verify that the printing settings are correct in both the application software and the printer driver. Also, check whether the problem is being caused by a PRESCRIBE command error. If the problem occurs only with a specific file or program, the most likely cause is an error in a parameter to a command or command syntax.
Explains standard copier paper compatibility and its impact on performance and machine longevity.
Provides guidelines on paper condition, composition, sizes, and smoothness for optimal printing.
Details various paper types supported by the printer, including plain, special, and custom types.
Introduces configuring the printer via the operation panel and alternative remote access methods.
Explains the LCD, keys, and indicators on the printer's operation panel for user interaction.
Guides users on navigating the printer's menu system to configure various settings effectively.
Details procedures for printing various reports like menu maps, status pages, and font lists.
Specifies settings for removing USB flash memory and printing its content.
Explains how to view the total number of pages printed by the printer.
Covers setting paper size and type for MP tray and cassettes, including custom paper adjustments.
Specifies printing parameters like quality, paper source, duplex printing, emulation, and page layout options.
Details TCP/IP (IPv4 and IPv6) settings, including DHCP, IP address, subnet mask, and gateway.
Covers common settings like message language, buzzer, RAM disk, memory card, and error handling.
Outlines functions to protect printer operation and print data, including ID, password, and interface blocking.
Provides procedures for setting and changing the administrator ID and password.
Provides options for adjusting print quality and performing printer maintenance, such as restarting the printer.
Lists available printer options to enhance printing capabilities and satisfy user requirements.
Explains how to install memory modules to improve print job performance and speed.
Describes the paper feeder accessory that adds two more paper cassettes for continuous feeding.
Details using CF cards for storing fonts, macros, and overlays, including installation procedures.
Provides information on using USB flash memory devices for storing print data and files.
Explains the connector specifications for USB and network interfaces used with the printer.
Details the Hi-Speed USB interface specifications, connectors, cable requirements, and pin assignments.
Covers network interface features, supported protocols, specifications, and operation environment.
Refers to imitating other manufacturers' printer operations, supporting various emulation modes.
A printing mode designed to reduce toner consumption, resulting in lighter printouts.
Explains the unique numerical identifier for computers and devices on a network.
Software enabling printing data from applications; installation is required on the connected computer.
A power-saving feature activated after a period of inactivity to reduce energy consumption.
General| Color | No |
|---|---|
| Duplex printing | Yes |
| Print technology | Laser |
| Maximum resolution | 1200 x 1200 DPI |
| Time to first page (black, normal) | 7 s |
| Print speed (black, normal quality, A4/US Letter) | 35 ppm |
| Memory type | DDR |
| Memory slots | 1 |
| Processor model | 440F5 |
| Processor family | PowerPC |
| Maximum internal memory | 1152 MB |
| Sound power level (standby) | 30 dB |
| Sound pressure level (printing) | 55 dB |
| Sound pressure level (quiet mode) | 49 dB |
| Total input capacity | 300 sheets |
| Maximum input capacity | 800 sheets |
| Total number of input trays | 2 |
| Maximum number of input trays | 4 |
| Multi-Purpose tray input capacity | 50 sheets |
| Mobile printing technologies | Not supported |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 11 W |
| Power consumption (printing) | 554 W |
| Power consumption (PowerSave) | 5.5 W |
| Printing colors | Black |
| Maximum duty cycle | 50000 pages per month |
| Recommended duty cycle | 2800 pages per month |
| Page description languages | Epson LQ, IBM ProPrinter, PCL 5e, PCL 6, PJL, PostScript 3 |
| Display | LCD |
| Certification | GS, TUV, CE |
| Product color | Black, White |
| Custom media width | 70 - 215.9 mm |
| Maximum print size | 216 x 356 mm |
| Custom media length | 148 - 356 mm |
| Duplex media weight | 60 - 105 g/m² |
| Paper tray media types | Plain paper |
| Paper tray media weight | 60 - 120 g/m² |
| Non-ISO print media sizes | Letter |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5 |
| Maximum ISO A-series paper size | A4 |
| Multi-Purpose Tray media weight | 60 - 220 g/m² |
| Standard interfaces | Ethernet, USB 2.0 |
| Server operating systems supported | Windows 2000 Advanced Server, Windows 2000 Server, Windows MultiPoint Server 2011, Windows SBS 2011 Essentials, Windows SBS 2011 Standard, Windows Server 2003, Windows Server 2003 R2, Windows Server 2003 x64, Windows Server 2008, Windows Server 2008 R2, Windows Server 2008 x64, Windows Server 2012 |
| Sustainability certificates | ENERGY STAR |
Weight and Dimensions| Depth | 393 mm |
|---|---|
| Width | 375 mm |
| Height | 267 mm |
To Next Page
