lamber 01F User Manual

8
INTRODUCTION ENGLISH
AND SAFETY NORMS
INTRODUCTION
- The machine 01F is an Industrial dish-washing machine .
- The machine is in conformity to the European Norms 89/336/CEE for the radio noises.
- According to EEC directive no. 23 of 19/02/1973 and the law of actuation no.791 of 18/10/1987, our
appliances are built-up according to the good technique notes in force in Italy and abroad.
- Noise level of the machine, less than 70 dB(A).
PRELIMINARY OBSERVATION
Carefully read the instructions reported in the present user manual, as it gives important indications about
safety of installation, operation and maintenance:
- carefully keep the present manual for further consultations;
- the illustrations and drawings showing the machine are intended for general reference only and are not
necessarily accurate in every instance;
- the dimensions and characteristics of the machine, given in this Manual, are not to be considered
binding and may be changed without prior notice;
- once removed the packing material, check that all the equipment is present. If there is any doubt, do
not use it and contact qualified personnel. The packing elements (plastic bags, nails, etc.) should be
kept away from children, because they are dangerous.
GENERAL SAFETY REGULATIONS
THIS SAFETY CODE HAS BEEN COMPILED IN YOUR INTEREST. Strict adherence to these rules will
reduce the risks of injury both to yourself and to others;
Personnel working with this machine must adhere strictly to all statutory safety regulations as well as the
specific rules listed below. Failure to do so may result in personal injury and damage to the machine;
- DO NOT attempt to move, install, set up or operate this machine until you have read and fully
understood this Manual. If doubt persists, ask your supervisor;
- never leave tools, parts or other loose material on or in the machine;
- Before switching the equipment on, make sure that the model plate data conform to those of the
electrical and water distribution network;
- remember that even with the mains indicator in the “OFF” position, the incoming cables are still live;
- BEFORE starting the machine or the cycle, after any maintenance or repair work, make sure all
protective are correctly installed;
- be vigilant at all times, remember that your safety and that of your fellow workers depends on you;
- when moving or lifting the machine, care must be taken to comply with all the relevant regulations
governing such operations;
- installation should be carried out by qualified personnel according to the manufacturer's instructions.
- this equipment should be destined to the use which it has been conceived for. Any other application
should be considered improper and consequently dangerous;
- the equipment should only be used by personnel trained for its use;
SPECIAL SAFETY REGULATIONS
- adjustement and repairs must be carried out only by qualified personnel. Repair carried out by
unskilled personnel may be dangerous;
- perfect washing-up results as regards hygiene and a correct operation of the washing machine can be
assured only in case the instructions reported in the present handbook are carefully followed;
- the machine must be used only by authorized personnel who must comply with sanitary measures;
- do not leave the machine in an environment with temperatures lower than 0°C;
- the machine protection degree is IP21, therefore it should not be washed with direct high pressure jets
of water.

lamber 01F Specifications

General

Brand	lamber
Model	01F
Category	Dishwasher
Language	English

Summary

Introduction and Safety Norms

Introduction

Basic information about the industrial dish-washing machine.

Preliminary Observations

Read manual, illustrations for reference, dimensions may change, check packing.

General Safety Regulations

Key safety rules to prevent injury and machine damage, emphasizing adherence to standards.

Special Safety Regulations

Specific safety rules for qualified personnel, operation, and environmental conditions.

Control Panel Functions

Main Switch and Indicator Lights

Explanation of the main switch (A) and indicator lamps for line (C), cycle (D), and temperature (E).

Cycle Start and Drain Controls

Details on the cycle pushbutton (B), drain pump (R), and its indicator lamp (H).

User Operation and Working

Machine Working and Use

Machine capacity, protection degree, object arrangement, and descaling advice.

Pre-Washing Operation Steps

Detailed sequence for loading detergent, dishes, and starting the wash cycle.

Washing Performance Troubleshooting

Troubleshooting common washing problems like dirt residuals or halos.

Washing Best Practices and Maintenance

Dish Positioning and Detergent Use

Guidance on positioning dishes and using detergents and rinse aids.

Specialized Maintenance Procedures

Instructions for descaling, sanitization, water softener regeneration, and salt control.

Cleaning, Maintenance, and Troubleshooting

Safety, Daily Cleaning, and Warnings

Precautions, daily routines, external washing prohibition, and troubleshooting faults.

Fault Diagnosis and Solutions

Addressing machine start-up, water supply, washing, and rinsing issues.

Drain Pump Operation and Stainless Steel Maintenance

Drain Pump Usage

Instructions for the operation of the drain pump.

Stainless Steel Care Guidelines

Guidelines for cleaning, daily care, and rust removal on stainless steel.

Installation Connection Diagrams

Water, Drain, and Electrical Connections

Schematics showing water inlet, drain, and electrical connections.

Installation Dimension Specifications

Details on maximum drain height and input connection points.

Installer Electrical Safety

Electrical Connection Requirements

Guidelines for safe mains connection, including switches, fuses, and cable types.

Grounding and Equipotential Bonding

Essential information on effective grounding and equipotential system connection.

Water System Specifications and Operation

Water Supply Parameters

Requirements for water pressure, temperature, and hardness.

Operational Temperatures and Calibration Warning

Recommended washing/rinsing temperatures and warning about thermostat calibration.

Water Drain Setup

Guidelines for the water drain pipe and siphon installation.

Timer and Program Controls

Timer Wiring Schematic

Electrical diagram showing the timer connections.

Wash Program Timing Table

A table detailing various wash cycle durations and pauses.

Adjusting Program Timings

Instructions on how to change program durations using the selector.

Regulation and Adjustment Schematics

Thermostat Adjustment Details

Diagrams showing how to adjust wash and rinse thermostats.

Rinse Aid Dispenser Settings

Instructions for adjusting the rinse aid dosage via the regulation screw.

Electrical Wiring Diagram

Main Electrical Components and Systems

Diagram showing major electrical components, including the control board and SRS system.

Electrical Component Identification

List and explanation of electrical components used in the diagram.