Why is the carbonator pump noisy on my lancer 14800 Beverage Dispenser?
If your carbonator pump is noisy or cavitating, verify that the incoming supply water pressure to the carbonator pump is a minimum of 25 psi and a maximum of 50 psi.
Why is there insufficient soda flow from my lancer 14800 Beverage Dispenser?
If you're experiencing insufficient soda flow from your Lancer Beverage Dispenser, ensure that the incoming CO2 pressure is between 70 and 75 psi. Also, check the shutoff valve on the mounting block to make sure it's fully open.
How to fix excessive foaming in my lancer 14800?
To resolve the issue of excessive foaming in your Lancer Beverage Dispenser: * Ensure the ice bin is full and allow the cold plate to re-stabilize. * Correct the incoming water or syrup temperature if it's too high. * Adjust the CO2 pressure downward, ensuring it remains above 70 psi. * Readjust and reset the ratio. * Clean the nozzle and diffuser. * Bleed air from the BIB lines.
What to do if no product is dispensed when the switch is activated on my lancer 14800, but the switch panel does light up?
If the switch panel lights up when activated, but no product is dispensed from your Lancer Beverage Dispenser, the issue could stem from: * A disconnected 25-pin valve harness. Turn off the power, reconnect the 25-pin harness, and restore power. * A faulty switch assembly, which would need replacement. * A faulty product solenoid, also requiring replacement.
Why is there insufficient water flow in my lancer 14800 for plain water drinks?
To address insufficient water flow for plain water drinks from your Lancer Beverage Dispenser, verify that the incoming supply water pressure to the plain water inlet is a minimum of 75 psi (maximum of 125 psi). Also, ensure that the shutoff valve on the mounting block is fully open. Additionally, check for any foreign debris in the water flow control and clean it out to ensure smooth spool movement. Finally, consider if there is a water filtration problem and service the water system as required.
Why does my lancer 14800 push chute, ice door open, motor runs, but no ice dispenses?
If the push chute opens the ice door, the motor runs, but no ice is dispensed (or the ice is of poor quality) from your Lancer Beverage Dispenser, it could be due to: * The dispenser being out of ice; fill the unit with ice. * A missing or damaged agitator pin; replace the agitator pin. * Poor ice quality; install water filtration/purification to the ice maker supply water.
Why am I experiencing erratic ratio in my lancer 14800?
If you're experiencing erratic ratio in your Lancer Beverage Dispenser, it could be due to the incoming water and/or syrup supply not being at the minimum flowing pressure; check and adjust the pressure. Additionally, foreign debris in the water and/or syrup flow control could be the cause; clean out any foreign material to ensure smooth spool movement. Lastly, the CO2 regulator might be malfunctioning; repair or replace as required.
What to do if valve will not shut off on my lancer 14800 Beverage Dispenser?
If the valve on your Lancer Beverage Dispenser won't shut off, try activating the valve a few times to dislodge any debris in the solenoid seat. If this doesn't work, remove the solenoid coil and plunger and clean out any foreign material. If the issue persists, the solenoid plunger might be sticking, and you should replace the solenoid coil.
Why does the BIB pump on my Lancer Beverage Dispenser fail to restart after replacing the bag?
If the BIB pump on your Lancer Beverage Dispenser fails to restart after a bag replacement, make sure the BIB connector is tightly secured. If it is, the connector might be stopped up, requiring cleaning or replacement. Also, check for any kinks in the syrup line and straighten or replace the line if necessary.
Why is my lancer 14800 dispensing only water or only syrup?
If your Lancer Beverage Dispenser is dispensing only water, no syrup, or syrup only, no water, consider the following: * The syrup BIB might be empty; replace as needed. * The water or syrup shutoff on the mounting block might not be fully open; ensure it is. * There might be an improper or inadequate water or syrup supply; check the supply. * The CO2 pressure to syrup pumps might be too low; ensure it's between 70-80 psi. * The BIB pump might be stalled or inoperative; check CO2 pressure and/or replace the pump. * There might be a kinked line; remove the kink or replace the line. * The CO2 regulator might be malfunctioning; repair or replace as required.
Guidelines for choosing an appropriate installation site.
Steps for physically setting up the beverage dispenser.
Exploded view and parts list for the final assembly.
Parts list and diagram for pellet ice assembly.
Electrical wiring schematic for 115V/60Hz units.
Plumbing diagram illustrating valve connections.
General| Brand | lancer |
|---|---|
| Model | 14800 Series |
| Category | Beverage Dispenser |
| Language | English |
To Next Page
