lancer BEVARIETY MCY-22

Questions and Answers

L
Lisa HopkinsAug 16, 2025
Why is my lancer BEVARIETY MCY-22 Beverage Dispenser producing excessive foaming?
- R
  rodriguezjamesAug 16, 2025
  Excessive foaming in your Lancer Beverage Dispenser can occur due to several reasons: * The incoming water or syrup temperature might be too high; correct this at the dispenser. * The water flow rate could be too high; readjust and reset the Brix. * The nozzle and diffuser may not be clean; remove and clean them. * They might also be improperly installed; remove and install them correctly. * The CO pressure might be too high; check for the proper pressure setting.
E
Elizabeth WeaverAug 19, 2025
What to do if my lancer BEVARIETY MCY-22 Beverage Dispenser dispenses only water or only syrup?
- I
  iwangSep 12, 2025
  If your Lancer Beverage Dispenser is dispensing only water or only syrup, start by checking the stems on the mounting block to ensure they are fully open. If the stems are open, remove the valve from the mounting block and open the stems slightly to check for proper syrup and water supply. If there is no supply, inspect the dispenser for freeze-up or other issues.
T
Timothy SmallAug 22, 2025
What to do if my lancer BEVARIETY MCY-22 Beverage Dispenser is not dispensing any product?
- J
  jimenezcarolAug 22, 2025
  If no product is dispensed from your Lancer Beverage Dispenser, ensure the water and syrup shutoffs are fully open by checking the stems on the mounting block. If it is a LEV model, make sure the cup lever arm or I.D. Panel actuator is activating the switch; if not, repair or replace it. Also for LEV models, check the electric current supplied to the valve against specifications, and if adequate, inspect the solenoid coil and switch, replacing if necessary. If these steps don't resolve the issue, remove the valve from the mounting block and open the stems slightly to check for proper water and syrup supply. If there's still no supply, check the dispenser for freeze-up or other problems. Finally, if it is a LEV model, check the manual operation of the valve to ensure proper function.
J
Jason RobinsonAug 26, 2025
Why won't the valve shut off on my lancer BEVARIETY MCY-22?
- C
  Courtney SanchezAug 26, 2025
  If the valve on your Lancer Beverage Dispenser won't shut off, the cup lever may be sticking or binding; correct or replace the lever. If it is a LEV model, check the switch for free actuation. Also for LEV models, the solenoid armature might not be returning to the bottom position; replace the defective solenoid armature or spring. Lastly, check for debris or damage to the paddle arms; remove any debris and/or replace any damaged paddle arms.
C
Charles ClarkAug 28, 2025
What causes erratic ratio Brix in my lancer BEVARIETY MCY-22 Beverage Dispenser?
- M
  Matthew SmithAug 28, 2025
  Erratic Ratio Brix in your Lancer Beverage Dispenser can be caused by insufficient flowing pressure in the incoming water and/or syrup supply; check to ensure sufficient flowing pressure. It can also be due to foreign debris in the water and/or syrup flow controls; remove the flow controls and clean out any foreign materials to ensure smooth free piston movements.
Y
ycrawfordAug 31, 2025
How to fix insufficient water flow in lancer BEVARIETY MCY-22 Beverage Dispenser?
- R
  Rodney HooverAug 31, 2025
  Insufficient water flow in your Lancer Beverage Dispenser may be due to low or restricted water flow pressure. Check the incoming water from the carbonator to ensure minimum flowing pressure, referring to the specifications. Also, check the stems on the mounting block to ensure they are in the fully open position. Another cause could be foreign debris in the water flow controls; remove the water flow control from the upper body and clean out any foreign materials to ensure smooth free piston movement.
C
Charles YoderSep 3, 2025
How to resolve insufficient syrup flow in Lancer Beverage Dispenser?
- B
  Belinda WestSep 3, 2025
  Insufficient syrup flow in your Lancer Beverage Dispenser may be caused by low or restricted syrup flowing pressure. Check the incoming syrup to ensure minimum flowing pressure, referring to the specifications. Also, check the shutoff on the mounting block to ensure it is in the fully open position. Another cause may be foreign debris in the syrup flow controls; remove the syrup flow control from the upper body and clean out any foreign materials to ensure smooth free piston movement.
M
matthewacostaSep 6, 2025
What causes water leakage around the nozzle of a lancer BEVARIETY MCY-22?
- D
  Dustin DeanSep 6, 2025
  Water leakage around the nozzle of your Lancer Beverage Dispenser can be due to an o-ring that is not properly installed above the diffuser; install or replace the o-ring correctly. It could also be because the o-ring is damaged or missing; replace the o-ring.
M
morganbellSep 9, 2025
Why is there leakage between the upper and lower bodies of my Lancer Beverage Dispenser?
- P
  Paula JohnstonSep 9, 2025
  Leakage between the upper and lower bodies of your Lancer Beverage Dispenser can be caused by one or more loose retaining screws; tighten all size retaining screws. It can also be due to paddle arm assemblies that are worn or damaged; replace the paddle arm assemblies.
B
Billy YoungSep 12, 2025
What causes miscellaneous leakage in my lancer BEVARIETY MCY-22 Beverage Dispenser?
- E
  Eric MillerSep 12, 2025
  Miscellaneous leakage in your Lancer Beverage Dispenser can be due to a gap between parts; tighten the appropriate retaining screws. It can also be caused by damaged, missing, or improperly installed o-rings; replace the appropriate o-rings.