To Next PageTo Next PageWhat to do if the deck cylinder will not retract on Land Pride Brush Cutter?
If the deck cylinder on your Land Pride Brush Cutter will not retract, it is likely because the cylinder rod is bent and needs replacement.
What to do if blades are breaking on my Land Pride Brush Cutter?
If the blades of your Land Pride Brush Cutter are breaking, it's likely due to hitting solid objects during operation. To prevent this, thoroughly check the cutting area before you start and stay alert while cutting to avoid any obstacles.
Why is the blade carrier bent on my Land Pride Brush Cutter?
If the blade carrier on your Land Pride Brush Cutter is bent, it's likely due to hitting solid objects. Replace the blade carrier and be more alert to avoid solid objects in the future.
What to do if the deck cylinder will not extend and/or retract on Land Pride Brush Cutter?
If the deck cylinder on your Land Pride Brush Cutter will not extend and/or retract, the orifice elbow on the rod end may be plugged; try cleaning the orifice fitting. Another possibility is a broken or disconnected wire on the solenoid; check the wiring on the cartridge valve solenoids.
Why is the PTO driveline bent on my Land Pride Brush Cutter?
If the PTO driveline of your Land Pride Brush Cutter is bent, it is likely contacting the drawbar or bottoming out. Reposition the drawbar, or replace the PTO tubes and cut them to the correct length.
What to do if electrical control push button switches do not work on Land Pride Brush Cutter?
If the electrical control push button switches on your Land Pride Brush Cutter aren't working, start by replacing the 10 AMP fuse. Ensure the circular plastic connector is properly connected to the receptacle. Check for power at the control stick connections and confirm that the tractor spool valve is engaged (open). Adjust the flow control valve, and verify that the hoses are connected to the correct duplex outlet on the tractor. Also, inspect the solenoid on the cartridge valve assembly for defects and clean or replace it if necessary. Finally, ensure the tractor hydraulic fluid level is adequate.
Why is my Land Pride Brush Cutter vibrating excessively?
Excessive vibration in your Land Pride Brush Cutter can stem from several causes. First, inspect and unlock any locked blades. If that's not the issue, the blades may have unequal weight, in which case you should replace them as a pair. A bent PTO driveline or blade carrier can also cause vibration, requiring straightening or replacement. Lastly, check if the PTO cross is not centered with the yoke; disassemble and inspect for incorrectly located needles or a damaged bearing cap.
Why are blades wearing excessively on my Land Pride Lawn Mower?
Excessive wear on your Land Pride Lawn Mower blades can occur if you're cutting on sandy ground or frequently hitting the ground. To resolve this, raise the cutting height.
What to do if blades are breaking on Land Pride RCP2660?
If the blades on your Land Pride Lawn Mower are breaking, it's likely due to hitting solid objects. Before you start cutting, thoroughly check the area. Stay alert while cutting to avoid any obstacles.
What causes blades wearing excessively on Land Pride Brush Cutter?
If the blades on your Land Pride Brush Cutter are wearing excessively, it could be because you are cutting on sandy ground or frequently contacting the ground. Raise the cutting height to address both of these issues.
General| Brand | Land Pride |
|---|---|
| Model | RCP2660 |
| Category | Lawn Mower |
| Language | English |
General precautions for safe operation and accident prevention.
Understanding the safety alert symbol and its importance.
Ensuring children's safety around operating equipment.
Proper procedures for safely shutting down and storing the tractor.
Specifications for tractors compatible with the rotary cutter.
Pre-operation checks to ensure safe and proper functioning.
How the breakaway feature works and how to reset it.
Key operational considerations for expert cutter use.
Fundamental steps for operating the rotary cutter.
General advice on servicing and maintaining the implement.
Inspection, sharpening, and replacement of cutting blades.
Diagrams and intervals for lubricating various components.
Common problems, their causes, and recommended solutions.
