Landa SLT Series - User Manual

Other manuals for Landa SLT Series

Questions and Answers

J
Jessica CameronAug 17, 2025
Why is the pressure fluctuating on my Landa SLT Pressure Washer?
- J
  jonesbonnieAug 17, 2025
  If your Landa Pressure Washer is experiencing fluctuating pressure, several components could be the cause. Start by checking the valves for wear or blockages and replace them if necessary. Inspect the pump for air leaks, paying attention to the water supply and joints in the suction line. Also, examine the piston packing for wear and replace it if needed. If operating the pressure washer at altitudes above 1000 feet, it may be necessary to adjust the engine. Contact your local authorized engine sales and service center for details.
C
colleenriosSep 4, 2025
What to do if my Landa SLT burner still won't light?
- D
  Derrick JeffersonSep 4, 2025
  If your Landa Pressure Washer burner won't light, ensure fuel is reaching the combustion chamber by checking the fuel pump for proper flow. Also, on machines with spray gun control, inspect the solenoid flow switch for proper on-off fuel flow control. Clean a clogged burner nozzle as required. If the thermostat is faulty or the engine speed is too slow, increase the engine RPM to increase voltage. Check the flow switch for malfunction by removing it, testing for continuity, and replacing it as needed. Replace the flow solenoid if it malfunctions.
W
wrightarielNov 10, 2025
How to fix low operating pressure in my Landa Pressure Washer?
- H
  Heather BradfordNov 10, 2025
  If your Landa Pressure Washer has low operating pressure, several factors could be the cause. Check for a faulty pressure gauge and replace it if necessary. Ensure there's sufficient water supply by using a larger supply hose and cleaning the filter at the water inlet. An old, worn, or incorrect spray nozzle can also cause this issue; match the nozzle number to your machine or replace it. Other potential causes include belt slippage (tighten or replace the belt), plumbing or hose leaks (check and re-tape with Teflon tape), a faulty or mis-adjusted unloader valve (adjust or install a repair kit), worn packing in the pump (install a new packing kit), fouled or dirty inlet or discharge valves in the pump (clean them), worn inlet or discharge valves (replace with a valve kit), an obstruction i...
W
William BaxterNov 21, 2025
Why is my Landa Pressure Washer smoking?
- J
  Julie BensonNov 22, 2025
  If your Landa Pressure Washer smokes while the burner unit is running, or only at cold-start when the burner is off, the fuel may be improper or contaminated with water. Drain the tank and replace the contaminated fuel. Improper air adjustment can also cause smoking; readjust the air bands on the burner assembly. Low fuel pressure (less than 140 psi for the burner) can be a factor, so adjust the fuel pump pressure to specifications. A faulty burner nozzle spray pattern can also cause smoking, so replace the nozzle, checking the parts breakdown for the correct nozzle size. A heavy accumulation of soot on the coil and burner assembly can cause smoking; remove the coils and burner assembly and clean them thoroughly. Check the smoke stack for obstructions such as insulation blockage or other f...
W
walkerdavidDec 1, 2025
Why my Landa SLT Pressure Washer burner will not light?
- C
  Cassandra ConradDec 1, 2025
  If your Landa Pressure Washer burner won't light, start by checking the fuel level and filling the tank if it's low. Ensure you're using the correct fuel and that it's not contaminated with water; if it is, drain the tank and refill. Inspect the fuel line for clogs and clean or replace it as needed. Replace the fuel filter if it's plugged. Make sure the burner air bands are properly adjusted for a clean burn. Verify the fuel pressure from the fuel pump is within specification; increase it or replace the pump if necessary, using a pressure gauge to test. Check the burner transformer for a proper arc between contacts and replace it if faulty. Ensure all electrical wire contacts are clean and tight, with no breaks in the wiring. If the flex coupling is slipping on the fuel pump or burner moto...