To Next PageTo Next PageWhy is my Landa VHP Pressure Washer relief valve leaking water?
If the relief valve is leaking water on your Landa Pressure Washer, it could be due to: * The wrong nozzle size or debris in the nozzle. Clean or replace it with the correct nozzle.
Why won't the pilot stay on in my Landa VHP Pressure Washer?
If the pilot ignites but will not stay on when the gas cock dial is released on your Landa Pressure Washer, it could be: * The pilot is too far away from the thermocouple. Adjust the thermocouple closer to the flame. * The thermocouple is loose at the regulator safety valve. Tighten it to a firm fit.
Why does my Landa VHP Pressure Washer pilot not light?
If the pilot on your Landa Pressure Washer does not light, it could be due to: * A closed manual pilot valve. Open the pilot valve. * A gas leak in the pilot. It is recommended to call a qualified serviceman. * A problem with the piezo ignitor. Adjust the spark gap and secure the wires.
Why is my Landa VHP burner smoking?
If your Landa Pressure Washer burner is smoking, it may be due to a stack restriction.
What to do if my Landa Pressure Washer is not steaming?
If your Landa Pressure Washer is not steaming, consider these potential causes: * Ensure the steam valve is open (counterclockwise). * Verify the burner switch is in the "ON" position. * The coil may be dirty or sooty. * The steam valve could be clogged; try cleaning or replacing it.
What causes pulsation in my Landa VHP Pressure Washer?
Pulsation in your Landa Pressure Washer is often caused by a faulty pulsation damper. Check the precharge; if it's low, recharge it or install a new one.
What to do if my Landa VHP Pressure Washer pump runs rough with low pressure?
If your Landa Pressure Washer pump runs extremely rough and the pressure is very low, the issue could be: * A restricted inlet or air entering the inlet plumbing. Ensure proper size inlet plumbing and check for an airtight seal. * Inlet restrictions and/or air leaks, or a stuck inlet or discharge valve. Replace worn cup or cups, clean out any foreign material, and replace worn valves.
Why is my Landa VHP pump so noisy?
A noisy pump in your Landa pressure washer can be due to: * Air in the suction line. Check the water supply and connections on the suction line. * Broken or weak inlet or discharge valve springs. Check and replace if necessary. * Excessive matter in valves. Check and clean if necessary. * Worn bearings. Check and replace if necessary.
General| Fuel Type | Gasoline |
|---|---|
| Drive | Direct drive |
| Hose Length | 50 ft |
| Pump | Triplex plunger pump |
| Frame | Steel frame with powder-coated finish |
Provides essential safety information and warnings for operating the pressure washer.
Details the procedures for installing, operating, and using the pressure washer effectively.
Covers procedures for proper upkeep, troubleshooting, and preventing damage.
Lists all components with part numbers for identification and ordering.
General introduction to safety practices and owner responsibilities for the pressure washer.
Critical warnings and precautions to prevent injury, property damage, and ensure safe operation.
Specific guidelines for safely handling and connecting propane tanks for the unit.
Diagram and labels identifying all parts and connections of the pressure washer.
Step-by-step instructions and considerations for setting up the pressure washer.
Detailed steps on how to start, operate, and shut down the pressure washer.
Guidelines for using detergents and effective cleaning methods with the unit.
Procedures for properly shutting down and cleaning the unit after use.
Instructions on how to store the pressure washer, especially during cold weather.
Specific steps for preparing the unit after prolonged periods of storage.
Guidance for maintaining the engine's performance and longevity.
Routine checks and actions to prevent issues and ensure optimal machine condition.
Information on adjusting and maintaining the unloader valves for correct pressure.
Steps to protect the machine from freezing damage during cold weather.
Details on the safety thermostat that controls water temperature.
Guidance on pump oil type, change intervals, and checking the oil level.
Procedure for removing lime and other deposits from the heating coils.
Instructions for removing and cleaning soot deposits from the heating coil.
Explanation of the pressure relief valve's function and when to repair or replace it.
Information about the rupture disk, its purpose, and replacement.
Considerations for propane cylinder size and its impact on burner performance.
A log for recording pump oil changes and operating hours.
Lists common problems, their possible causes, and recommended solutions.
Exploded view and parts list for the left side assembly of the Landa VHP unit.
Exploded view and parts list for the right side assembly of the Landa VHP unit.
Detailed parts list for various components of the Landa VHP series.
Diagram and parts list for the hose and spray gun assembly.
Exploded view and parts list specific to the LB Series Pump.
Diagram and parts list for the VRT3 Unloader assembly.
Diagram and parts list for the detergent injector assembly.
