Lascar Electronics EasyLog User Manual

3
4
1
2
We recommend that a new CR1620 battery is used if any low battery state is detected by the software or if a large proportion of the
typical 30 day battery life has been consumed. Remove the screw. Pull the two halves of the case apart. Remove the old battery. Insert
the new battery. Assemble the two halves of the case. Insert the screw and tighten.
EL-USB-LITE
REPLACING YOUR DATA LOGGER’S BATTERY
Your data logger is provided with a 3.6V 1/2AA battery already installed. You can change the battery by following the instructions below.
3
4
1
2
DOWNLOAD AND INSTALL
EASYLOG USB SOFTWARE
Windows™ 7/8/10 (32 & 64bit)
Visit www.easylogusb.com and click
‘Download’. Once downloaded, install the
software. You may need administrator
permissions to do so.
•Insert the data logger into an available USB port on
your computer.
•Double click on the EasyLog USB icon on
your Windows™ desktop. This will load
the conguration software. Click ‘Set
up and start the USB data logger’ and
follow the set-up wizard.
•When setup is complete, the data logger should be
removed from the USB port. Do not leave your data
logger in the USB port for extended periods as this will
cause some of the battery capacity to be lost (with the
exception of EL-USB-1-RCG as this is a rechargeable
device).
•You can also download the data from a logger that has
been recording or view previously saved data from the
software. After doing so, remember to set-up and start your
logger to begin a new logging session.
USING THE SOFTWARE
Before using the data logger you will need to insert the 3.6V 2/3AA High Temperature battery provided, following the instructions below.
EL-USB-1 PRO
The EL-USB-1-RCG’s battery is preinstalled. To charge the battery, connect to a USB port with a USB cable until the green LED shows.
The rechargeable battery should only be replaced by an authorized supplier. Note that only the battery of the EL-USB-1-RCG is
rechargeable. Do not attempt to recharge any other device.
1
2
3
4
EL-USB-1-RCG
EL-USB
Quick Start Guide

Lascar Electronics EasyLog Specifications

General

Brand	Lascar Electronics
Model	EasyLog
Category	Data Loggers
Language	English

Summary

Download and Install EasyLog USB Software

EasyLog USB Software Installation

Instructions for downloading and installing the EasyLog USB software from the official website.

Using the EasyLog USB Software

Connect and Configure Logger

Steps to connect the data logger via USB and configure it using the software wizard.

Logger Management and Data Download

Guidance on removing the logger from USB, downloading data, and preparing for new logging sessions.

Data Logger Battery Replacement

EL-USB-1 PRO Battery Installation

Instructions for inserting the 3.6V 2/3AA High Temperature battery into the EL-USB-1 PRO model.

EL-USB-1-RCG Battery Charging

Information on charging the pre-installed rechargeable battery for the EL-USB-1-RCG.

EL-USB-LITE Battery Replacement

Guide on replacing the CR1620 battery in the EL-USB-LITE model, including disassembly.

LED Status Indicators

EL-USB LED Status Indicators

Explanation of LED flashes for EL-USB models (excluding EL-USB-1-PRO) indicating logging, alarms, and battery status.

EL-USB-LITE LED Status Indicators

Explanation of LED flashes for EL-USB-LITE, indicating logging, alarms, and battery status.

EL-USB-1-RCG LED Status Indicators

Explanation of LED flashes for EL-USB-1-RCG, indicating logging, alarms, and battery status.

Important Safety Information

Repairing or Modifying

Warning against attempting to repair or modify Lascar products, as it may void the warranty.

Disposal and Recycling Information

Guidelines for disposing of Lascar products, including electronic components and batteries, according to regulations.