LawnMaster L10 - Preparation; Select the Proper Base Station Location

14
ASSEMBLY
Preparation
Ŷ&DUHIXOO\UHPRYHDOOFRQWHQWVIURPWKHSURGXFWSDFNDJLQJ
Ŷ(QVXUH\RXKDYHDOOWKHDFFHVVRULHVDQGWRROVQHHGHGIRUDVVHPEO\DQGRSHUDWLRQ7KLVDOVR
includes suitable personal protective equipment.
Ŷ'XULQJLQVWDOODWLRQRIWKHEDVHVWDWLRQDQGWKHERXQGDU\ZLUH\RXZLOODOVRQHHGUXEEHUPDOOHW
and pliers (not included in the box).
Know Your Lawn (See Figs. 1-2)
Understanding your lawn will reduce unnecessary mistakes and make the whole installation
process easier and smoother.
Ŷ,IWKHUHDUHVWRQHVRQWKHODZQWKDWPD\GDPDJHWKHPRZHUWKH\VKRXOGEHUHPRYHGRU
excluded from the working area (Fig. 1).
Ŷ,QVSHFWWKHODZQIRUKROHVRUKROORZV)LOOWKHPZLWKWRSVRLOWRSUHYHQWUDLQZDWHUIURPIRUPLQJ
pools of water on the lawn and to prevent mower from becoming stuck. The mower may be
damaged if it is operated in pools of water (Fig. 2).
Ŷ%HIRUHOD\LQJWKHERXQGDU\ZLUHLWLVUHFRPPHQGHGWRXVHWKHROGODZQPRZHURUJUDVVWULPPHU
to cut the grass very low on your lawn. This will help insert wire pegs easier, and the boundary
wire can be laid as close as possible to the ground to protect the boundary wire from being cut
by the mower.
Select the Proper Base Station Location (See Figs. 3-4)
The base station sends safe, low voltage control signals along the boundary wire and charges the
robotic mower. It is important to select a proper location for the base station.
Ŷ0DNHVXUHDPLQLPXPPRIVWUDLJKWZLUHLVODLGLQIURQWRIWKHHGJHRIWKHSODWHDQGEHKLQGWKH
base station to allow smooth docking (Fig. 3).
Ŷ7KHZKROHSRZHUFRUGLVQRPRUHWKDQP0DNHVXUHWKHEDVHVWDWLRQLVQHDUDZDOORXWOHW
Ŷ7KHOHYHOVXUIDFHWRSODFHWKHEDVHVWDWLRQRQLVIUHHRIDQ\VKDUSREMHFWV
Ŷ7KHPRZHUFDQEHRSHUDWHGLQPXOWL]RQHODZQV3ODFHWKHEDVHVWDWLRQLQWKHODUJHVW]RQHLI
WKHUHDUHDGGLWLRQDO]RQHVLQ\RXUODZQ
Ŷ7KHVXUIDFHWKHEDVHVWDWLRQLVORFDWHGRQVKRXOGEHVKDG\HYHQDQGÀDW
Ŷ,WLVUHFRPPHQGHGWRSODFHWKHEDVHVWDWLRQLQDGU\DQGVKHOWHUHGORFDWLRQ
NOTE: The base station should be placed on relatively level ground. The ground on each side of
the base station should be level for minimum 1m without corners, slopes or obstacles to ensure
proper docking (Fig. 4).