LeapFrog Leapster 2 - Troubleshooting; Common Issues and Solutions; Touch Screen Calibration

AC Adapter Electrical Ratings:
U.S., CAN Input: ~ 120VAC, 60Hz
U.K. Input: ~ 230VAC, 50Hz
Australia and New Zealand Input: ~ 240VAC, 50Hz
Output: === DC9V, 700mA, 6.3VA
Consignes de sécurité pour l'utilisation de l'adaptateur
(Adaptateur vendu séparément ; produit LeapFrog Enterprises, Inc.)
A AVERTISSEMENT : Le cordon de l'adaptateur peut provoquer un risque d'étranglement.
A ATTENTION : CE JOUET FONCTIONNE À L'ELECTRICITE
Ne convient pas aux enfants de moins de 3 ans. Comme tous les objets utilisant du courant électrique,
ce produit doit être manipulé avec précaution pour éviter tout risque de décharge électrique. À UTILISER
UNIQUEMENT EN INTERIEUR, DANS UN ENDROIT SEC.
Le transformateur n'est pas un jouet et il est recommandé que ce soit un adulte qui le branche à la prise
murale. Pour éviter tout danger d'incendie, d'électrocution ou de blessure, veillez à contrôler périodiquement
l'état du cordon électrique, de la fiche d'alimentation électrique, des lames de contact, du boîtier ou de toute
autre partie. Dans un tel cas, le transformateur doit être réparé avant d'être réutilisé.
* Le jouet doit seulement être utiliser avec l'adaptateur recommandé.
* Le jouet ne doit pas être branché à plus d'accessoires que le nombre recommandé.
* Débrancher le jouet de l'adaptateur avant de le nettoyer avec du liquide.
* Pour nettoyer l'adaptateur, débranchez-le d'abord de la prise murale et utilisez ensuite un tissu
humide pour le nettoyer.
Voltage de l'adaptateur
Voltage d'entrée pour les Etats-Unis et le Canada : -120VAC, 60Hz
Voltage d'entrée pour le Royaume Uni : ~230VAC, 50Hz
Voltage d'entrée pour l'Australie et la Nouvelle Zélande : ~240VAC, 50Hz
Voltage de sortie : === DC9V, 700mA, 6.3VA
USB Cable
Use only the USB cable provided by LeapFrog Enterprises, Inc. Using any other cable may exceed FCC and other
regulatory emissions limits. The USB cable is not a toy. Disconnect the toy from the USB connection before cleaning.
Cable USB
Utilisez exclusivement le câble USB fourni par LeapFrog Enterprises, Inc. L'utilisation d'un autre câble peut
dépasser les limites de la FCC (Commission fédérale américaine des communications) et autres limites
règlementaires en matière d'émission. Le câble USB n'est pas un jouet. Déconnectez le jouet du port USB
avant d'entamer toute opération de nettoyage.
Touch Screen Calibration
Your LEAPSTER2 handheld touch screen has already been calibrated for use, but if you experience either
example below, you may adjust the calibration yourself:
* Lines drawn with the stylus appear to be offset from the location of the stylus tip.
* Objects you are trying to select are not being chosen.
Follow these steps to calibrate the touch screen:
1. Hold down the Hint button while turning the unit on.
2. When the LEAPSTER® menu screen appears, press the A button.
3. Touch each of the crosshairs that appear with the stylus.
4, Restart unit.
Country Selection
Selecting your country of residence adjusts the phonetic pronunciation of some letters to better match your
country's language. If you need to change your country selection, follow these steps:
1. Press the On/Off button to turn on your system.
2. When the sign-in screen appears, press these buttons all at the same time:
a. Home button
b. D-pad right arrow button
c. B button
3. Follow the on-screen instructions.
Troubleshooting
Symptom Try This
Toy does not turn on or does not respond Make sure the handheld is turned on
Make sure batteries are correctly installed
Make sure battery cover is securely attached
Remove batteries and put them back in
Clean battery contacts by rubbing lightly with a soft eraser
and then wiping with a clean and dry cloth
Install new batteries
Display stops working Install new batteries
Trouble accessing or playing Connect the LEAPSTER2 handheld to the computer and
downloaded games follow directions to connect
Touch Screen Touch Screen Calibration
-Objects you are trying to select are
not being chosen
- Lines drawn with the stylus are offset
from the location of the stylus tip
- Refer to the Touch Screen Calibration procedure
included in this Parent Guide
FCC NOTICE:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
«Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by LeapFrog Enterprises, Inc., could
void the user's authority to operate the equipment.