This document is the owner's manual for the 23" Electric Fireplace Log Set, model number EF290A. It provides comprehensive information on the product's function, technical specifications, usage, and maintenance.
Function Description
The 23" Electric Fireplace Log Set is designed to provide the ambiance of a traditional fireplace with the convenience and safety of an electric unit. It features a realistic flame effect with three settings, a heater with two power options (750W and 1500W), and a thermostat for temperature control. The unit can be operated via a manual control panel located on the device or a remote control. It is intended for indoor use and is designed to be inserted into an existing fireplace opening or a custom-built enclosure.
Important Technical Specifications
- Model: EF290A
- Voltage: 120V
- Wattage (min/max): 750W / 1500W
- Frequency: 60 Hz
- BTU (max): 4600
- Amperage: 12.5A
- Heating Area (max): 400 square feet
- Product Dimensions:
- Width: 22 7/8" (581mm)
- Height: 19 1/8" or 19 7/8" (486mm or 505mm)
- Depth: 9 7/16" (240mm)
- Power Cord Length: 6 feet
- Minimum Opening Dimensions for Best Flame Effect:
- Width: 23 23/26" (605mm)
- Height: 22 1/8" (561mm)
- Depth: 11 7/16" (291mm)
Usage Features
The fireplace log set offers several features for ease of use and safety:
- Manual Control Panel:
- POWER SWITCH: Turns the main power on/off. A "beep" sound indicates the switch is turned ON.
- FLAME: Cycles through three flame settings (full bright flame + little blue, full bright flame, half bright flame) and off.
- HEATER: Cycles between Low (750W) and High (1500W) heat settings, and off. An indicator light illuminates when the heater is on. The heater can be used without the flame. The fan operates 10 seconds ahead of the heater and stops 10 seconds later.
- THERMOSTAT: A rotary switch to set the desired room temperature from 1 to 9. The thermostat maintains the selected level by turning the heater on/off.
- Remote Control: A handheld remote control provides convenient operation of the unit.
- POWER: Turns the unit on/off and recalls previous settings.
- FLAME: Cycles through flame settings.
- CRACKLING: Turns the crackling sound on/off, with normal and high crackling sound options.
- LOW HEAT: Turns the heater on at half heat setting.
- HIGH HEAT: Turns the heater on at full heat setting.
- Temperature Limiting Control: The heater is equipped with a temperature limiting control that automatically turns off the heater if an unsafe temperature is reached.
- Safety Information: The manual emphasizes crucial safety warnings, including:
- Always read all instructions before use.
- The heater is hot when in use; avoid direct skin contact.
- Keep combustible materials at least 3 feet (0.9m) from the front of the heater.
- Extreme caution is necessary when the heater is used by or near children or invalids, and whenever the heater is left operating and unattended.
- Always unplug the heater when not in use.
- Do not operate the heater with a damaged cord or plug or after malfunctions; service by qualified personnel is required.
- Do not use outdoors.
- Not intended for use in bathrooms, laundry areas, or similar indoor locations.
- Do not run power cord under carpeting.
- Connect to properly grounded outlets only.
- Do not insert or allow foreign objects into any ventilation or exhaust opening.
- Do not block air intakes or exhaust.
- A heater has hot and arcing or sparking parts inside; do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Only use this heater as described in this manual.
- Always plug heaters directly into a wall outlet/receptacle; never use with an extension cord or relocatable power tap.
- Ensure the plug is very tightly connected and no other appliances are plugged onto the same circuit.
- Do not operate if damaged or malfunctioned; contact service technician.
Maintenance Features
Regular maintenance helps ensure the longevity and safe operation of the fireplace log set:
- Cleaning:
- Always turn the heater OFF and unplug the power cord from the outlet before cleaning.
- Never immerse in water or spray with water.
- Buff using a soft cloth, slightly dampened with a citrus oil-based product.
- Do NOT use brass polish or household cleaners as these products will damage the metal trim.
- NEVER use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
- Vents: Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
- Logs and Base: The log set should not be operated with an accumulation of dust or dirt. Vacuum the log set as needed. Use a damp cloth and a mild detergent to clean painted surfaces. Never use abrasive cleaners.
- Flame Screen: The flame screen is cleaned in the factory during assembly. Dust particles can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, clean the flame screen with a damp cloth; never use abrasive cleaners.
- Maintenance:
- Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside!
- ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury.
- Electrical and Moving Parts:
- The fan motors are lubricated at the factory and will not require lubrication.
- Electrical components are integrated in the fireplace and are not serviceable by the consumer.
- Storage: Store heater in a clean dry place when not in use.
- Replacement Parts:
- Use only replacement parts supplied by the manufacturer.
- No internal parts are replaceable or serviceable by the user.
The manual also includes a troubleshooting guide to help users diagnose and resolve common issues, such as the unit not turning on, the heater not working, or the flame not appearing. For issues that cannot be resolved through troubleshooting, users are advised to contact customer service.
To Next Page
Need help?
General
