LEGRAND DW-311 - Product Specifications; General Specifications; Coverage and Dimensions; Installation and Wiring

Order wall plate separately.
Catalog # Color Voltage Load Rating
DW-311-W White 120VAC; 50/60Hz
or
277VAC; 50/60Hz
@
120VAC: 0-1000W ballast, E-ballast, LED,
tungsten; 1/4hp motor
or
@
277VAC: 0-1200W ballast, E-ballast,
LED; 1/4hp motor
DW-311-LA Lt. Almond
DW-311-I Ivory
DW-311-G Grey
DW-311-B Black
DW-311-R Red
DW-311-347-W White 347VAC; 50/60Hz 0-1500W ballast, LED; 1/4hp motor
DW-311-347-LA Lt. Almond
DW-311-347-I Ivory
DW-311-347-G Grey
DW-311-347-B Black
DW-311-347-R Red
WWW.LEGRAND.US/WATTSTOPPER
Ordering Information
• DW-311: 120/277VAC; 50/60Hz
• DW-311-347: 347VAC; 50/60Hz
• Dimming control signal: 0-10VDC, sinks up to 50mA for
control of compatible ballasts (12 if each sources 2mA);
Class 1 wiring
• Time delays: 3, 5, 15 or 30 minutes, walk-through, test-mode
• Power up after power loss: On, Off or last state
• Coverage: Major motion, PIR 35’ x 30’, Ultrasonic 20’ x 20’
Minor motion, PIR 20’ x 15’, Ultrasonic 15’ x 15’
• Sensitivity adjustment: PIR (high/low), Ultrasonic (fully
variable)
• Dimensions (L x W x D): 2.73” x 1.75” x 1.81” (69mm x 44mm
x 46mm)
• UL and cUL listed (E101196)
• Five year warranty
Specifications
Installation and Wiring
Pub. No. 46901 Rev. 11/2016
Product Controls
Coverage Patterns
For best performance,
Legrand recommends
using this sensor in
spaces no larger than
18’ x 15’.
PIR
Coverage
7.5’
(2.2m)
15’
(4.5m)
20’
(6.1m)
35’
(10.6m)
Major motion
Minor motion
Ultrasonic
Coverage
10'
(3.0m)
7.5’
(2.2m)
20’
(6.1m)
15’
(4.5m)
Major motion
Minor motion
4’
(1.2m)
20’
(6.1m)
35’
(10.6m
)
0
Wiring Diagrams
Multi-way wiring
Driver
or Ballast
Red
Black
Neutral
Line
Green
White
Ground
Violet
Yellow
Gray
0-10V
Dimming
Black
Violet
Black
Neutral
White
Line
White
Ground
Green
Ground
Green
Yellow
traveler
Yellow
Red
Gray
Red
Violet
Gray
Connect 0-10V
leads to dimming
ballast from one
DW-311 only
Driver
or Ballast
Note: Requires Class 1 wiring for 0-10V dimming.
DELAY
MODE
ADDITIONAL
FEATURES
Ultrasonic
Sensitivity
Adjustment
Trimpot
TRIGGER
Button
Hinges
Tabs
Dip Switches
Detection LED
Red = PIR
Green = Ultrasonic
PIR Lens
Up Button
Down Button
Ultrasonic Cones
DIP Switch Settings
=ON =OFF
1
Auto - On
Manual - On
Mode
9
12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR
=ON =OFF
1
Auto - On
Manual - On
Mode
9 12345678
Time
Delay
Mode
ON
Additional
Features
Trigger
Test/3 min
15 minutes
30 minutes
5 minutes
23
Time Delay
Exit Programming Mode
Audio Alert
Walk-Thru
Visual Alert
67
Additional Features
89
PIR Sensitivity
High Trim
Low Trim
Ramp Up Time
Fade Down Time
Light Level Adjust
Power Loss Mode
Presentation Mode
Service Mode
Preset On Level
Non-Dim Mode
Green LED # of Blinks
1=OFF, 2=ON
1=ON, 2=OFF
1=OFF, 2=ON
1=100%, 2=50%
1=1, 2=2.5, 3=5, 4=10s
1=2.5, 2=5, 3=15, 4=30s
1=Last Non-Zero Value,
2=50%, 3=75%, 4=100%
1=10V, 2=Manual Adjustment
1=0V, 2=Manual Adjustment
1=Disable, 2=Enable,
3=Smart Light Level
Reset To Default
1=Keep Last State,
2=Default On, 3=Default Off
1=OFF, 2=ON
1=ON, 2=OFF
Press and Hold UP or
DOWN for 5 seconds
1=OFF, 2=ON
Default Values Shown in Bold
45
Trigger
Mode
Initial
Occupancy
Maintain
Occupancy
Re-trigger
Option C
Both Both Both
Standard
EitherEither
Option A
Either EitherPIR
Both
Option B
PIR PIR PIR