Lennox Baltic BHK 070 - Page 90

IOM / ROOFTOP BALTIC Series - 0704-E Page 89
Terminal display address configuration
The address of the terminal must be checked after having powered
the board.
- To access the configuration mode, press  together and old
them for at least 5 seconds.
- The screen shown in
Fig28 will be displayed with the cursor
flashing in the top left hand corner.
- To change the address of the terminal display press the  key
once.
- Use the  keys to select the desired value and confirm by
pressing  .
- If the address was changed it will display the screen shown in
Fig29 .
CONTROL INTERFACE DC50
Display adressDisplay adress
Display adressDisplay adress
Display adress
settings ....: nnsettings ....: nn
settings ....: nnsettings ....: nn
settings ....: nn
I/O Board adress:XXI/O Board adress:XX
I/O Board adress:XXI/O Board adress:XX
I/O Board adress:XX
Fig. 28
Display adressDisplay adress
Display adressDisplay adress
Display adress
changedchanged
changedchanged
changed
Fig. 29
Assigning Terminal displays to control boards.
- Access the configuration mode by pressing  for at least 5
seconds.
NOTE : To access the board address menu you must go directly to
the bottom of the first screen (shown in
Fig30 ) without changing
the terminal address as explained above.
- Press the  key until the cursor moves to the field "I/O Board
address :XX".
Fig 30
- Use the key to select the correct Climatic board.(N° of Unit)
- Pressing  again will display the screen shown in
Fig 31 .
- Pressing  again will display the screen shown in
Fig 32 .
- The field "P:XX " shows the address of the selected board. In the
example the value "12" has been selected.
- The filed under the "Adr" column represents the addresses of
the terminal displays associated with the board that has the address
"12", while the column under "Priv/Shared " indicate the type of
terminal selected.
Ph: Private
Sh :Shared
Sp : Shared Printer (N/A)
- To exit the configuration procedure and save the data, select the
filed "OK?NO", choose "Yes" using the  keys and confirm by
pressing  .
If the terminal remains inactive (no button is pressed) for 30 se-
conds, the configuration procedure is aborted automatically.
Terminal ConfigTerminal Config
Terminal ConfigTerminal Config
Terminal Config
Press ENTERPress ENTER
Press ENTERPress ENTER
Press ENTER
To continueTo continue
To continueTo continue
To continue
Fig. 31
P12:Adr Priv/P12:Adr Priv/
P12:Adr Priv/P12:Adr Priv/
P12:Adr Priv/
SharedShared
SharedShared
Shared
Trm1 17 prTrm1 17 pr
Trm1 17 prTrm1 17 pr
Trm1 17 pr
Trm2 32 shTrm2 32 sh
Trm2 32 shTrm2 32 sh
Trm2 32 sh
Trm3 None --OK? NOTrm3 None --OK? NO
Trm3 None --OK? NOTrm3 None --OK? NO
Trm3 None --OK? NO
Fig. 32
Display adressDisplay adress
Display adressDisplay adress
Display adress
settings ....: 17settings ....: 17
settings ....: 17settings ....: 17
settings ....: 17
I/O Board adress:XXI/O Board adress:XX
I/O Board adress:XXI/O Board adress:XX
I/O Board adress:XX
Fig. 30
Keys
Decrease a
value or go to
"Override
menu"
Change
field or
validate
24.2°C ON24.2°C ON
24.2°C ON24.2°C ON
24.2°C ON
FA:20%FA:20%
FA:20%FA:20%
FA:20%
DynFan:AutoDynFan:Auto
DynFan:AutoDynFan:Auto
DynFan:Auto
Out:40.0°C Z:AOut:40.0°C Z:A
Out:40.0°C Z:AOut:40.0°C Z:A
Out:40.0°C Z:A
CoolCool
CoolCool
Cool
Set time
Back to main
Screen or
Cancel
"Override"
Time zone
settings
Increase a
value or go to
"Override
menu"