WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are not sure about any part of these instructions, consult an electrician.
• Use this device with copper or copper clad wire only.
• To avoid damage to the product, DO NOT use disinfecting products, including foggers, sprays or other types of atomized cleaning agents.
• DO NOT spray liquid onto the product.
• To clean use a damp cloth with mild soap
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320
(Canada Only) www.leviton.com
PK-A3061-10-02-0M
WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!
1. Remove existing wallplate and switch or dimmer, if applicable.
2A. TO SIDE WIRE: Remove insulation from each circuit conductor per strip gauge on device [approx. 3/4" (1.9 cm)]. Connect wires per appropriate WIRING DIAGRAM as follows:
Loop wires clockwise 3/4 turn around terminal screws. Tighten terminal screws over wire loops using the appropriate torque value, which can be found at Leviton.com/torquevalue.
NOTE: Terminal screws accept up to #12 AWG copper or copper-clad wire.
2B. TO BACK WIRE: Remove insulation from each circuit conductor approx. 1/2" (1.3 cm).
Connect wires per appropriate WIRING DIAGRAM as follows: Insert straight wires under clamps next to appropriate terminal screws. Tighten terminal screws using the appropriate
torque value, which can be found at Leviton.com/torquevalue.
NOTE: Back wire accepts up to #10 AWG copper or copper-clad wire.
3. Using the long mounting screws provided, mount device into outlet box with a minimum depth of 2-3/4" (7.0 cm).
4. Mount wallplate and tighten cover screws.
5. Restore power at circuit breaker or fuse.
INSTALLATION IS COMPLETE.
© 2022 Leviton Mfg. Co., Inc.
PK-A3061-10-02-0M
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
INSTALLATION INSTRUCTIONS
ENGLISH
INSTALLATION
Key Lock Switches
Cat. No. 1221-2KL Single Pole - Cat. No. 1222-2KL Double Pole
Cat. No. 1223-2KL 3-Way - Cat. No. 1224-2KL 4-Way
Cat. No. 2KL Replacement Keys (2 per package)
Rated: 20A-120/277VAC - 1 Hp@120V, 2 Hp@240V
LIMITED 10 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship
under normal and proper use for ten years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.
leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product
is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in
accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied
warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to ten years. Leviton
is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or
delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Line Hot (Brass Screw)
Ligne active (vis laiton)
Linea Fase (Tornillo de latón)
1
2
Neutral (White)
Neutre (blanc)
Neutro (Blanco)
3
Ground (Green Screw)
Terre (vis verte)
Tierra (Tornillo Verde)
Load (Brass Screw)
Charge (vis laiton)
Carga (Tornillo de latón)
4
Single Pole / Unipolaire / Unipolar
2
3
1
4
Load
Charge
Carga
3
Line Hot (Black Screw) Circuit B
Ligne active, circuit B (vis noire)
Linea Fase (Tornillo Negro) Circutio B
2
3
Load (Brass Screw) Circuit A
Charge, circuit A (vis laiton)
Carga (Tornillo de latón) Circutio A
Line Hot (Black Screw) Circuit A
Ligne active, circuit A (vis noire)
Linea Fase (Tornillo Negro) Circutio A
1
5
Ground (Green Screw)
Terre (vis verte)
Tierra (Tornillo Verde)
Double Pole / Bipolaire / Dos Polos
Load (Brass Screw) Circuit B
Charge, circuit B (vis laiton)
Carga (Tornillo de latón) Circutio B
4
3-Way | 3-voies | 3-Vías
Travelers Brass Screw to Brass Screw
Cavalier de vis laiton à vis laiton
Viajeros Tornillo Latón a Tornillo Latón
To Common Terminal (Black Screw)
Vers la borne commune (vis noire)
A Terminal Común (Tornillo Negro)
Neutral (White)
Neutre (blanc)
Neutro (Blanco)
1
2
3
Ground (Green Screw)
Terre (vis verte)
Tierra (Tornillo Verde)
4
4-Way | 4-voies | 4-Vías
1 1
2
Load
Charge
Carga
Load
Charge
Carga
4 4 4 4
3 3
1 1
2
4 4 4
4
4
4
4 4
3 3 3
Motor
Moteur
Motor
Travelers between switches
Cavaliers entre les interrupteurs
Viajeros entre interruptores
To Common Terminal (Black Screw)
Vers la borne commune (vis noire)
A Terminal Común (Tornillo Negro)
Neutral (White)
Neutre (blanc)
Neutro (Blanco)
1
2
3
Ground (Green Screw)
Terre (vis verte)
Tierra (Tornillo Verde)
4
1
2
4
5
3-Way
3 voies
3 Vías
3-Way
3 voies
3 Vías
OUT
SORTIE
SALIDA
OUT
SORTIE
SALIDA
IN
ENTRÉE
ENTRADA
IN
ENTRÉE
ENTRADA
4-Way
4 voies
4 Vías
To Next Page
Need help?
General
