1 2 3 4
65 7 8
An iOS (12.0 or later) or Android (8.0 or later)
mobile device.
NOTE: Make sure Wi-Fi and Bluetooth are enabled on
your mobile device.
A My Leviton cloud account
(set up through the My Leviton app).
A 2.4GHz Wi-Fi network with high
speed internet.
Installation requires electrical knowledge.
If you are unsure of any steps, consult an electrician.
Getting Started Guide
Cat. No. D26HD
DIMMER
2
ND
GEN
See the complete line of My Leviton
TM
app compatible
dimmers, switches, plug-ins, and controllers at
leviton.com/decorasmart
Features
Before you install Identify your wires
What you need to make
it work:
Your dimmer
works with:
Leviton’s second-generation
Decora Smart Wi-Fi Dimmer makes
it easier than ever to control your
lights how you want. Use your
voice with Amazon Alexa, Google
Assistant, or Apple Siri — or
use your smartphone or tablet
to control lighting with the My
Leviton app, even when you’re
away from home.
The Decora Smart Wi-Fi Dimmer
looks right at home with your
other Decora
®
in-wall devices
and features intuitive on/off and
dim/bright control easily used by
anyone in the house.
Combine with other Decora Smart
Wi-Fi devices to create a whole
home experience with room
scenes, activities, and schedules
for connected lights to match
your lifestyle.
• Dimmable LED, dimmable CFL,
incandescent, and MLV lighting.
• Do not use your dimmer with metal
wall plates, electronic low voltage,
motor loads, or aluminum wire.
• When two or more dimmers are
installed next to each other, the load
ratings become 500W incandescent
and 500VA MLV for each dimmer.
No reduction is necessary if the load
is LED or CFL.
• For compatible LED bulbs, go to
leviton.com/LED.
• Additional self-service support
options can be found in the My Leviton
app or at leviton.com/decorasmart.
RATINGS
General Use 120VAC, 60Hz
LED / CFL 300W
Incandescent 600W
MLV 600VA
Operating Temp 0°C - 40°C (32°F - 104°F)
Operating Humidity 0 - 90% non-condensing
NETWORK
Wi-Fi 802.11 b/g/n networks - 2.4GHz only
Security
WPA, WPA2, or WPA3 security, or open
Bluetooth v5.0
MY LEVITON APP
iOS version 12.0 or later
Andr
oid version 8.0 or later
DI-000-D26HD-02A
Dim / bright bar
Manually adjust light levels.
Air gap switch
This feature will stop power
to the dimmer. Gently pull
bottom out until a click is
heard. Power to the dimmer
and indicator lights will
turn off. After servicing is
complete, push back in for
normal operation.
Rocker
• Press the top to turn the
light ON.
• Press the bottom to turn
the light OFF.
• Double press the top turn
ON at max brightness.
Off means off
• Ensures low-wattage LED
bulbs always turn OFF.
Brightness indicator lights
• Displays light level when
adjusting brightness.
Status LED
• Illuminates when the lights
are OFF so you can find the
dimmer in the dark.
• Provides connectivity and
device status feedback.
• Advanced settings available
in the My Leviton app.
Check your wall box:
1. Remove wallplate and disconnect existing switch.
2. Restore power. Carefully test wires with voltage tester to
find the line (hot) wire.
3. Turn off power at the circuit breaker.
4. Mark the wires as shown below. Please note neutral wires
are required to operate this device.
Quick tip: Neutral wires are typically white and will be
found bundled inside the electrical box.
Single pole installation:
1. Work only one connection at a time.
2. Connect wires as shown using the included
wire connectors.
1. Restore power. Status LED should flash GREEN indicating
your dimmer is ready to be enrolled.
2. After powering on the dimmer to confirm it is receiving
power, turn the power back off again at the breaker prior
to completing the installation.
Wire your dimmer
Test and install
Welcome
Things to consider:
To control the dimmer from more than one location such
as in a 3-way or multi-way, you will need either a wired
DD00R or DD0SR Companion device, or a wireless DAWDC
or DAWSC Anywhere Companion device. See Dimmer or
Switch Companion instructions for connection directions.
If your wall box looks different, call an electrician.
If your wall box contains a different wiring
configuration, contact Leviton’s technical support
team or consult an electrician.
WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off
power at the circuit breaker.
NOTE:
• Neutral connection is required.
• The YELLOW/RED traveler wire is only used in 3-way
applications; remember to put a wire connector on the
YELLOW/RED traveler even if not in use.
If you need help...
ONLINE
decorasmartsupport.leviton.com
CHAT
www.leviton.com/support
EMAIL
dssupport@leviton.com
CALL
1-800-824-3005 (USA)
1-800-405-5320 (Canada)
Easy Wi-Fi lighting
control for the
whole home
CHAT
www.leviton.com/support
CALL
1-800-824-3005 (USA)
1-800-405-5320 (Canada)
ONLINE
decorasmartsupport.leviton.com
EMAIL
dssupport@leviton.com
We are here to help
LINE
LOAD
TRAV
NEUTRAL
GND
GROUND
To Next Page
Need help?
General
