Leviton RTD01-10 User Manual

4 Speed Quiet Ceiling Fan/Light Control – Single Pole (One location)
Cat. No. RTD Ø 1-1 Ø ,
Fan Control
Rated: 1.5A-120VAC, 60Hz
Full Range Dimming Incandescent Lamp Load
Rated: 300W-120VAC, 60Hz
INSTALLATION INSTRUCTIONS
DI-000-RTD01-02B
Tools needed to install your Fan Speed
Control:
Slotted/Phillips Screwdriver Electrical Tape
Pliers Pencil
Cutters Ruler
Color Change Option:
If a color change kit is provided with your device,
proceed with the following step if you need to change
the color. Otherwise, proceed with the "Installing
Fan Speed/Light Control by itself or with other
devices" section.
Changing the color of your Fan Speed/
Light Control
Your Fan Speed Control includes two color options. The
Control ships with the White frame attached. To change
color of frame, proceed as follows:
Installing Fan Speed/Light Control by
itself or with other devices:
If installing Control in a single device application,
proceed with the MULTI-FAN CONTROL section. If
installing Control in a multi-device application,
proceed as follows:
MULTI-DEVICE APPLICATION
NOTE: There is NO derating necessary for multi-gang
installations of this Fan Speed Control.
MULTI-FAN CONTROL
Any number of fans of the same type may be
controlled by a single fan speed control provided that
the total amperage of the fans do not exceed the
amperage of the fan speed control.
INSTALLING YOUR FAN SPEED/LIGHT
CONTROL
NOTE: Use check boxes when Steps are
completed.
WARNING: To avoid fire, shock, or
death; TURN OFF POWER at circuit
breaker or fuse and test that power is off
before wiring!
Step 1
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFFONOFF
ONOFF
ONOFF
ONOFF
ONOFF
WARNINGS AND CAUTIONS:
•To be installed and/or used in accordance with appropriate electrical codes
and regulations.
• If you are unsure about any part of these instructions, consult a qualified
electrician.
•To avoid overheating and possible damage to this device and other equipment,
do not install to control a receptacle, fluorescent lighting, a motor- or a
transformer-operated appliance other than appropriate ceiling fans and
incandescent lamps.
WARNINGS AND CAUTIONS:
•To reduce the risk of fire or electrical shock, this control is to be used with
ceiling fans that are marked as suitable for use with solid-state fan speed control
and is rated 120VAC, total load 1.5 amperes maximum.
•For use on ceiling paddle fans with split-capacitor or shaded pole motors only.
Please refer to manufacture's instructions or rating label on the motor to
confirm type. Use with any other types of motors or equipment may cause
overheating and/or damage to the motors or equipment.
• Disconnect power at circuit breaker or fuse when servicing fixture.
• Use this device only with copper or copper clad wire. With aluminum wire use
only devices marked CO/ALR or CU/AL.
Strip 5/8"
(1.6 cm)
Cut
(if necessary)
√
Single-Pole Wiring Application:
Preparing wires:
Black
Red
Neutral
Green
Ground
Yellow
O
F
F
M
A
X
H
I
M
E
D
L
O
O
F
F
M
A
X
H
I
M
E
D
L
O
Push in side at tab
to release. Remove
frame and knob.
Press on knob. Line up
tabs on back of frame and
press in side to attach
Strip Gage
• Pull off pre-cut insulation from Control leads.
• Make sure that the ends of the wires from the
wall box are
straight (cut if necessary) .
• Remove 5/8" (1.6 cm) of insulation from each
wire in the wall box (shown).
Step 3
Step 2
Insert wires
straight then twist
clockwise
Electrical
Tape
5/8"
(1.6 cm)

Leviton RTD01-10 Specifications

General

Voltage	120VAC
Wireless Protocol	Z-Wave
Technology	Z-Wave Plus
Color	White
Protocol	Z-Wave
Load Type	Incandescent, LED
Compatibility	Z-Wave Hubs
Warranty	5 years

Summary

4 Speed Quiet Ceiling Fan/Light Control – Single Pole (One location)

General Safety Warnings and Cautions

General warnings and cautions regarding installation and safe use of the fan control device.

Tools Required for Installation

Lists the necessary tools for installing the fan speed control, including screwdrivers and pliers.

Color Change Option

Instructions on how to change the color frame of the fan speed control device.

Multi-Device and Multi-Fan Control Notes

Information on multi-gang installations, derating, and controlling multiple fans with one control.

Installation Procedure Steps

Step-by-step guide for installing the fan speed/light control, starting with safety.

Single-Pole Wiring Application and Testing

Step 3a: Single-Pole Wiring Application Continued

Detailed wiring instructions and diagram for connecting the control to the fan and light.

Step 4: Testing Fan Speed/Light Control

Procedure for testing the control's functionality before final mounting in the wall box.

Step 4a: Dimmer and Fan Speed Testing

Specific tests for dimmer brightness and fan speed adjustments.

Step 5: Fan Speed/Light Control Mounting

Instructions for safely mounting the control into the wall box after testing.

Step 6: Restore Power and Complete Installation

Final step to restore power at the breaker and confirm installation is complete.

Step 7: Operation Guide

How to operate the dimmer and fan speed controls after installation.

Troubleshooting Common Issues

Solutions for problems like fan/light not turning on or fan speed issues.

Product Information and Warranty

Technical Support and Website

Contact information for technical assistance and the manufacturer's website.

Wire Nut and Conductor Size Chart

A chart to guide the selection of appropriate wire nuts for conductor combinations.

Limited 5 Year Warranty

Details of the manufacturer's 5-year warranty, exclusions, and claim process.