10
Antenna Connections
Connecting an Outdoor Antenna
For the best reception, we recommend you use an
outdoor antenna
.
Severely
weathered antennas and antenna cables
can
reduce the signal quality. Before connecting it,
necessarily
inspect them. Any service center can
explain the various outdoor antennas available to
you
.
300 Ohm Flat Wir
e
1. Connect the 300 ohm flat wire to screws on the
300 ohm to 75 ohm adapter
.
2. Push the end of 300 ohm to 75 ohm adapter
into 75 ohm antenna jack.
75 Ohm Coaxial Cable
1.
Connect the 75 ohm coaxial cable directly to
the antenna jack
.
Connecting a CATV Cable
If you subscribe to a CATV system, change the
antenna connection as described below.
1. Remove the 300 to 75 ohm adapter or the
cable from the set if attached
.
2.
Connect the CATV cable (75 ohm coaxial
cable) to the 75 ohm antenna jack.
Connection of external equipment (some models)
You can connect additional equipment, such as
VCRs,
camcorders etc. to your set. Here shown
may
be somewhat different from your set. These
are an example drawing of typical jack layout
.
1.
IN 1 JACKS: Connect external equipment
outputs (VCR, LASER DISC, CAMCORDER) to
these inputs. Press the TV/VIDEO button to
select
VIDEO1 or VIDEO.
2. IN 2 JACKS: Connect external equipment
outputs (VCR, LASER DISC, CAMCORDER) to
these inputs. Press the
TV/VIDEO button to
select
VIDEO2 or S-VIDEO.
3.
OUT JACKS: Connect external equipment
inputs (VCR, Audio amplifier) to these output
s
for recording or monitoring the selecte
d
program
.
4.
§/ EARPHONE JACK (some models): In
some models, this jack is located on the front or
side of TV
.
Note: This TV is programmed to remember which
mode it was last set to, even if you turn the TV off.
Connecting AUDIO/VIDEO IN Jacks
1. Connect the audio/video output jacks of the VCR to
IN
1(A/V) jacks on the side or back of TV.
2. Press the TV/VIDEO button to select
VIDEO1 or
VIDEO.
Note: In some stereo models, if you connect the
audio/video output jacks of the VCR to the
IN 2 (A/V)
jacks on the front or side of TV, select
VIDEO2.
3. Press the PLAY button on the VCR.
The video playback is on the TV screen.
Note:
In case of MONO VCR, connect the output
jack
of VCR to the AUDIO L/MONO IN jack of TV
so that the
sound can be heard from both speakers.
If you
connect it to the AUDIO R IN jack of TV the
sound
is heard only from right speaker.
Note: In some mono models, when the input jacks
on the front panel and back panel are connected to
external equipments at the same time, the input
jacks on the front panel have priority over the
input jacks on the back panel of the TV.
Connecting the S-VHS VCR
(some models)
1. Connect the S-VHS output jack of the VCR to the
S-VIDEO jack on the side or back of TV.
2. Connect the audio/video output jacks of the VCR
to the IN 2(A/V) jacks on the front or side of TV.
3. Press the TV/VIDEO button to select
S-VIDEO
.
4. Press the PLAY button on the VCR.
The video playback is visible on the TV screen.
VCR Recording
(some models)
1. Connect the audio/video input jacks of the
recording VCR to the OUT (A/V) jacks on the back.
2. Select the program number on the TV.
3. Set the recording VCR to record.
Recording a program from con-
necked other equipment
(some models)
1. Connect the output jacks of the playback VCR
to the IN 1(A/V) jacks on the side or back of TV.
2. Connect the input jacks of the recording VCR to
the OUT (A/V) jacks on the back of TV.
3. Press the TV/VIDEO button to select
VIDEO1
or
VIDEO
.
If you connect it to the IN 2 (A/V) jacks on the
side of TV, you should select
VIDEO2
.
4. Press the PLAY button on the playback VCR
and set the recording VCR to record.
To Next Page
Loading...
