(3) EDID for HDMI-3 (DDC (Display Data Channel) Data)
(4) EDID for RGB
4. MST3361M-Set Adjustment
4-1. Synopsis
The Component 480i/1080p RGB 1080p adjustment sets the
optimal black level and gain automatically from the analog =>
digital converter, and is the function to correct the RGB
deviation.
4-2. Test Equipment
Adjustment remote controller, 801GF (802B, 802F, 802R),
MSPG925FA, MSPG-1025D Pattern Generator (480i/
1080P Horizontal 60Hz Color Bar Pattern output must be
possible and output level must be adjusted accurately to
0.7±0.1Vp-p.)
4-3. Adjustment
(1) How to adjustment the Component1
1) Input color bar pattern of 480i 60Hz mode that is supported
to Component 1 input and select ‘Component 1’.
2) After receiving signal for at least 1 second, press the
ADJ Key on the Service R/C to enter the ‘Ez - Adjust’
and select the ‘1. ADC 480i Comp1’. Press the Vol+
Key to adjust the component1.
3) When the adjustment is completed normally, a message
saying “ADC Component1 Success” is displayed and
when the adjustment is not completed normally, a
message saying ‘ADC Component1 480i Fail’ is
displayed.
4) When the component is not connected, a message
saying ‘Component1 Not Connected’, when the input
format is not 480i, a message saying ‘Not Valid Format’
and when the input signal is not coming out, a message
saying ‘Check Signal Status’ is displayed for 1 second.
(2) How to adjustment the Component2, RGB
1) Input color bar pattern of 1080p 60Hz mode that is
supported to Component 2, RGB input and select
‘Component 2’.
2) After receiving signal for at least 1 second, press the
ADJ Key on the Service R/C to enter the ‘Ez-Adjust’ and
select the ‘2. Adjust 1080p Comp2/ RGB’. Press the
Vol+ key to adjust the component 2.
3) When the adjustment is completed normally, a message
saying ‘ADC Component2 Success’ is displayed. and
when the adjustment is not completed normally, a
message saying ‘ADC Component2 1080p Fail’ is
displayed.
4) When the adjustment is not normally completed, make
the adjustment again after checking the pattern or
adjustment condition. The error message is as 4-3/ (1)/
4).
5) After adjustment is complete, exit the adjustment mode
by pressing the ADJ KEY.1
- 10 -
LGE Internal Use OnlyCopyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes
(Fig. 2) Adjust Pattern :100% 8 Color Bar Pattern
0123456789ABCDEF
000FFFFFFFFFFFF001E6D010001010101
10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CE 00 31 40 45 40 61 40 81 80 A9 40
30 D1 C0 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1A 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 00
0123456789ABCDEF
0 02031EF14E2022101F0102 0304051293
10 14 07 16 23 15 07 50 66 03 0C 00 30 00 80 01 1D
20 00 72 51 D0 1E 20 6E 28 55 00 C4 8E 21 00 00 1E
30 01 1D 80 18 71 1C 16 20 58 2C 25 00 C4 8E 21 00
40 00 9E 8C 0A D0 90 20 40 31 20 0C 40 55 00 4C 6C
50 42 00 00 18 01 1D 00 BC 52 D0 1E 20 B8 28 55 40
60 C4 8E 21 00 00 1E 01 1D 80 D0 72 1C 16 20 10 2C
70 25 80 C4 8E 21 00 00 9E 00 00 00 00 00 00 00 38
0123456789ABCDEF
000FFFFFFFFFFFF001E6D010001010101
10 0E 11 01 03 18 73 41 96 0A CF 74 A3 57 4C B0 23
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
30 D1 C0 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
40 36 00 C4 8E 21 00 00 1A 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 59
0123456789ABCDEF
0 020304000E1F008051001E3040803700
10 C4 8E 21 00 00 1C 00 00 00 00 00 00 00 00 00 00
20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 25
To Next Page
Loading...
