LG GR-282MF - User Manual

SERVICING PRECAUTIONS
Air Recharging in Compressor
Test the refrigeration by connecting it electrically before
refilling operation. It is necessary to ascertain the function
of the motor*compressor and identify the defects
immediately. Ifthe defects have been found, empty the old
system of eventual R-12 residue by breaking off the end of
the extension piece at its narrow point. (Figure 1)
Replace the filter and any damaged components. Unsolder
and pull off the piece remaining inside the service tube and
then attach an extension completely with male Hansen and
last, solder it to the same tube again. (Figure 2)
POINT TO BE
BROKEN
SERVICE TUBE EXTENSION
Figure 1
CHARGE TUBE
EXTENSION
MALE HANSEN
SOLDERING POINT
Figure 2
It is necessary to execute the soldering operation with
valve open so that the fumes caused by oil residue can
come out freely without blowholes between two tubes
during heating the point to be soldered.
The extension fitted with the male Hansen is connected to
the female fitting of the vacuum pump tube. (Figure 3)
puOMT_ cUUM
PRESSURE
GAUGE
Figure 3
Air evacuating from the system begins so soon as the
pump starts. The refrigeration system must be kept under
vacuum until the reading on the low-pressure gauge
indicates vacuum (0 absolute, -1 atm., -760 mm hg) in any
case it is advisable to keep the pump running for about 60
minutes. (Figure 3)
In case that a considerable leakage occurs and to stop the
vacuum pump will be necessary and add a small quantity
of Freon to the system, if vacuum should not be obtained
(pressure gauge can't fall to 1 atmosphere), start the
refrigeration unit and find the leakage with the special leak-
finder. When the defective soldering point is visible, re-do it
after opening the extension tube valve and reestablishing
the normal outside pressure inside the group.
Because the melted alloy is sucked into the tubes and
block them, the pressure must be rebalanced when
vacuum is in the system in soldering. As soon as the
vacuum operation is over, add the quantity in grams of
R-12 to the refrigerant system. Remember that every
system has an exact quantity of R-12 with a tolerance of
+5 grams that can be added. (Figure 4)
TO THE R-12 CYLINDER
_= J_ TOsTTHEEMREgRIGERATION
Figure 4
Before performing this operation (if the vacuum pump and
refilling cylinder are connected), make sure that the valve
placed between the vacuum pump and refilling tube are
closed to keep the Freon for adding to the system. (Figure 5)
FILLING OR VALVE TQ BE OPENED
CHARGE TUBE WHEN REFILLING
TO THE REFRIGERATION TO THE CHARGE
SYSTEM CYLINDER
VALVE TO BE CLOSED
AFTER VACUUM
TO THE VACUUM PUMP
Figure 5
In addition, check the graduated scale on the cylinder for
the quantity of R-12 to be added, for example, if we have
750 grams of Freon in the cylinder and must add 165
grams to the group, this amount will be reached when
R-12 has dropped to 585 grams, remembering that the
indicator shows a lower limit of meniscus. Do this after
choosing the scale corresponding to the gas pressure
different scales reported as the same gas pressure
indicated by the pressure gauge on the top of the column.
To make R-12 flow into the system, open the valve placed
at the base of the cylinder and connected to the filling tube.
The amount of Freon cannot be added to the system all at
once because it may cause a blocking of
motor-compressor. Therefore, proceed by adding original
quantity of about 20-30 grams and close the valve
immediately.
The pressure rises and the motor-compressor must start,
sucking the gas and making the pressure go down again.
Regulate the valve again, maintaining the same manner
until reaching to the quantity of R-12 established for the
system being charged. When the system is running, the
suction pressure must be stabilized between 0.10 to 0.4
atmosphere.
-3-

Summary

Servicing Precautions

Air Recharging in Compressor

Procedure for recharging refrigerant, including vacuuming and filling.

Specifications

GR-242 M;MV;S;SV Specifications

Technical specifications for the GR-242M/MV/S/SV refrigerator model.

GR-282 M;MV;S;SV Specifications

Technical specifications for the GR-282M/MV/S/SV refrigerator model.

GR-242 MF;MVF;SF;SVF Specifications

Technical specifications for the GR-242MF/MVF/SF/SVF refrigerator model.

GR-282 MF;MVF;SF;SVF Specifications

Technical specifications for the GR-282MF/MVF/SF/SVF refrigerator model.

Parts Identification

Disassembly

How to Replace Door Opening Type

Instructions for converting the refrigerator door opening direction.

Lamp Replacement

Step-by-step guide for replacing the internal lamp.

Adjustment

Compressor

Explanation of the compressor's role, composition, and usage notes.

PTC-Starter

Details on PTC starter composition, role, circuit, and usage.

OLP (Over Load Protector)

Definition, role, and diagram of the Over Load Protector.

Circuit Diagram

Troubleshooting

Compressor and Electric Components

Troubleshooting steps for compressor and related electrical components.

PTC and OLP

Troubleshooting procedures for PTC starter and Over Load Protector.

Defrost Timer

Troubleshooting steps for the defrost timer operation.

Another Electric Components

Troubleshooting guide for other electrical components affecting cooling.

Service Diagnosis Chart

A chart detailing complaints, points to check, and remedies for common issues.

Refrigerating Cycle

Troubleshooting chart for issues related to the refrigerating cycle (leakage, clog, compression).

General Control of Refrigerating Cycle

GR-282

LG GR-282MF Specifications

General

Brand	LG
Model	GR-282MF
Category	Refrigerator
Language	English