What to do if LG LCG3011BD top burners do not light?
If the top burners on your LG cooktop aren't lighting, first ensure the cooktop is properly plugged into a grounded electrical outlet. Also, the burner slots on the side of the burner may be clogged. In this case, remove and clean the burners. Check the electrode area for burned-on food or grease. Finally, make sure the burner parts are correctly installed.
Why are the LG LCG3011BD burner flames very large or yellow?
Large or yellow burner flames on your LG cooktop often indicate an improper air to gas ratio. If your cooktop is connected to LP gas, contact the person who installed your range or made the conversion.
How to check LG Cooktop burner flames?
To determine if your LG cooktop burner flames are normal, visually inspect them. Normal burner flames should appear as B or C, depending on the type of gas you use (see illustrations in the manual). Some yellow tipping on outer cones is normal with LP gas. If the flames look like A, it indicates a problem, and you should call for service.
Safety requirements for electrical connections, including cord condition and proper grounding.
Precautions concerning the safe use of the appliance by or around children.
Guidelines for safe operation of the cooktop during cooking and general use.
Procedures and precautions for safely cleaning the cooktop and its components.
Tips to prevent damage to the cooktop during operation and maintenance.
Guidelines for environmentally responsible disposal of worn-out appliances.
Read all instructions and notes for installer and consumer before starting installation.
Unpack and visually inspect the cooktop for any damage or missing components.
Provides minimum clearance dimensions and cutout dimensions for installation.
Steps for locating utilities, inserting the cooktop into the cutout, and securing it.
Ensuring correct gas pressure and type (natural or LP) for cooktop operation.
Procedure for connecting the gas supply line, including safety precautions.
Details on electrical requirements, grounding, and proper outlet connection.
Instructions for sealing any openings behind the cooktop and in the cabinet floor.
Guidance on correctly placing burner caps and heads over electrodes.
Procedure to verify proper ignition and operation of all surface burners.
Visual assessment of burner flame quality for natural and LP gas.
Steps to adjust the low flame setting for surface burners to achieve desired simmer.
General guidelines for using surface burners, including grate placement and burner operation.
Procedure for igniting gas surface burners using the electric ignition system.
Information on the features and benefits of sealed gas burners for cleaning and flexibility.
Instructions for lighting gas burners manually during an electrical power failure.
Tips on adjusting flame size to match cookware for efficient heating and safety.
Recommendations for suitable cookware materials and types for gas cooktops.
Precautions and guidelines for using woks and stove-top grills on the cooktop.
Instructions for cleaning sealed burner assemblies, including burner grates, caps, and heads.
Detailed steps for cleaning burner caps and heads, including soaking and manual scrubbing.
How to clean burner grates, including position-specific instructions and dishwasher safety.
Methods for cleaning the cooktop surface, especially stainless steel, and avoiding damage.
Specific cleaning instructions for stainless steel surfaces, including recommended cleaners and wiping direction.
Guidelines for cleaning control knobs, including removal and reinstallation procedures.
Procedure for disassembling and removing the cooktop plate for replacement.
Step-by-step instructions for removing and replacing a single burner body component.
Procedure for removing and replacing the electrode assembly, commonly known as a spark plug.
Steps for removing and replacing the spark module or ignition transformer.
Instructions for removing and replacing the ignition switch assembly.
Procedure for removing and replacing individual burner valves.
Instructions for removing and replacing the assembly of pipes that deliver gas to the burners.
Procedure for removing and replacing the manifold pipe assembly.
Steps for removing and replacing the main manifold assembly.
Procedure for removing and replacing the inlet pipe assembly.
Instructions for removing and replacing the bracket that supports the center burner.
Procedure for removing and replacing the left and right side burner brackets.
Steps to convert the gas regulator for operation with LP gas.
Procedure for replacing natural gas orifice spuds with LP gas orifice spuds.
Tables showing BTU ratings and orifice codes for LP and Natural gas.
Instructions for installing the choke and self-threading screw on the center burner.
Adjusting the low flame setting after gas conversion for optimal simmering.
Information on applying LP conversion stickers and converting back to original gas.
Flow chart to diagnose and troubleshoot 'No Ignition' problems with the cooktop.
Diagnosing and solving issues with yellow or yellow-tipped burner flames.
Troubleshooting large or yellow burner flames, possibly related to air-to-gas ratio.
Solutions for control knobs that are difficult to turn or do not operate correctly.
Diagnosing why top burners fail to light or burn unevenly.
General| Style | sealed burner; drop-in |
|---|---|
| Color | black stainless steel |
| Griddle | no |
| Continuous Grates | yes |
| Burner Type | sealed gas burner |
| Number of Burners | 5 |
| Downdraft Vent | no |
| Control Type | knobs |
| Fuel | natural gas; gas |
| Voltage | 120 volts |
| Current | 20 |
Weight and Dimensions| Depth | 19 11/16"; 21 11/16 inch; 21 11/16" |
|---|---|
| Height | 3 3/4 inch |
| Width | 28 1/2"; 30 inch; 30" |
| Cutout Depth | 19 11/16 inch |
| Cutout Width | 28 1/2 inch |
To Next Page