LG LF62 Series - Antenna Connection; Satellite Dish Connection; CI Module Connection

ENGLISH
13
NOTE
• The external device connection may dier from the model.
• Connect external devices to the TV regardless of the order of the
TV port.
• If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
• Refer to the external equipment’s manual for operating
instructions.
• If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
• In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
• In PC mode, some resolution settings may not work properly
depending on the graphics card.
• If Ultra HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Only UF67**)
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal amplier properly to
improve the image quality.
• If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
• An antenna cable and converter are not supplied.
• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
• For a location that is not supported with Ultra HD broadcasting,
this TV cannot receive Ultra HD broadcasts directly. This TV cannot
receive Ultra HD (3840 x 2160 pixels) broadcasts directly because
the related standards have not been conrmed. (Only UF67**)
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
HDMI ULTRA HD deep colour
settings
(Only UF67**)
• SETTINGS PICTURE HDMI ULTRA HD Deep Colour
HDMI (1/2) ULTRA HD Deep Colour
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 50/60 Hz (4:2:0)
• All HDMI ports support the HDCP 2.2.
• 4K Source is only supported in HDMI input.
• 4K signal and content are not available in the RF/USB input.
• All HDMI input ports support 4K @ 50/60 Hz (For details on the
supported specications, refer to the table below.) for high-
denition video. Picture or sound may not be supported depending
on the specications of the external device connected. In that case,
change the settings for HDMI ULTRA HD Deep Colour.
4K @ 50/60 Hz Support Format
Resolution
Frame rate
(Hz)
Colour Depth /
Chroma Sampling
8 bit 10 bit 12 bit
3840 x 2160p
4096 x 2160p
50.00
59.94
60.00
YCbCr 4:2:0 YCbCr 4:2:0
1
YCbCr 4:2:2
1
YCbCr 4:4:4
1
- -
RGB 4:4:4
1
- -
1 : Only supported when HDMI ULTRA HD Deep Colour turned “On”.
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
• Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
• If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.