To Next PageTo Next PageHow to fix an LG LH-T502SH Receiver remote control that is not working?
If your remote control isn't working, try these steps: * Make sure you're pointing the remote directly at the remote sensor on the LG DVD/CD Receiver. * Ensure you are within approximately 23 feet (7 meters) of the receiver. * Remove any obstacles that might be blocking the path between the remote and the receiver. * Replace the batteries in the remote with fresh ones.
Why is there no picture on my LG LH-T502SH?
There might be several reasons why you're not seeing a picture: * Ensure your TV is set to the correct video input mode to receive the signal from the LG DVD/CD Receiver. * Check that the video cable is securely connected to both the receiver and the TV. * Verify that the connected TV is powered on.
What to do if LG Receiver remote control is not working?
If the remote control for your LG DVD/CD Receiver isn't working correctly, consider the following: * Ensure the remote is pointed directly at the receiver's remote sensor. * Make sure you are within 23 ft (7 m) of the receiver. * Remove any obstacles between the remote and the receiver. * Replace the remote's batteries with new ones.
Why is there loud hum or noise heard on LG LH-T502SH Receiver?
If you hear a loud hum or noise from your LG Receiver, try the following: * Clean the disc. * Ensure the speakers and components are securely connected. * Move your TV away from the audio components.
What to do if there is no picture on my LG Receiver?
If there is no picture on your LG Receiver, here are a few things to check: * Ensure the TV is set to the correct video input mode to receive the DVD signal output. * Verify the video cable is securely connected to the jacks. * Make sure the connected TV is turned on.
Why is my LG LH-T502SH remote control not working?
If the remote control for your LG Receiver isn't working correctly, consider these potential causes: * The remote control might not be pointed at the remote sensor of the receiver; point it directly at the sensor. * The remote control might be too far from the receiver; use it within about 23 ft (7 m). * There might be an obstacle in the path between the remote control and the receiver; remove any obstacles. * The batteries in the remote control might be flat; replace them with new ones.
What to do if my LG Receiver remote control isn't working?
If your LG Receiver remote control isn't working correctly, consider these potential solutions: * Ensure that you are pointing the remote control at the remote sensor on the DVD/CD Receiver. * Make sure you are using the remote control within about 23 ft (7 m). * Remove any obstacles that might be blocking the path between the remote control and the DVD/CD Receiver. * Try replacing the batteries in the remote control with new ones.
Why is there no sound from my LG LH-T502SH?
If you're not hearing any sound or only a very low-level sound from your LG Receiver, here are a few things to check: * Ensure the equipment connected with the audio cable is set to receive DVD audio signal output by selecting the correct input mode on the audio receiver. * Verify that the audio cables are securely connected into the jacks. * Make sure the equipment connected with the audio cable is turned on. * If none of these steps work, the audio connecting cable might be damaged; consider replacing it.
How to improve poor playback picture on LG LH-T502SH Receiver?
If the playback picture quality is poor, consider the following: * Clean the disc. * Insert a disc. Ensure that the DVD or audio CD indicator in the DVD display is lit. * Insert a playable disc, verifying the disc type, color system, and regional code. * Place the disc with the playback side down. * Ensure the disc is placed correctly within the guide on the disc tray. * If a menu is on the TV screen, press the SETUP button to turn it off. * If the Rating level is set, cancel the Rating function or change the rating level.
What to do if radio stations cannot be tuned in on LG LH-T502SH Receiver?
If you're having trouble tuning into radio stations: * Check that the antenna is securely connected and properly positioned. * If using automatic tuning, the signal strength of the stations may be too weak, try tuning in the station manually. * If tuning by scanning preset stations, preset the stations.
General| Type | Home Theater System |
|---|---|
| Number of Channels | 5.1 |
| Audio Formats Supported | Dolby Digital, DTS |
| Connectivity | Optical |
| Supported Formats | MP3, WMA |
