To Next Page
J
jennifer86Sep 5, 2025
What to do if my LG Washer experienced a power failure?
- SsamanthafrederickSep 5, 2025
If your LG washer experienced a power failure, restart the cycle.
What to do if my LG Washer experienced a power failure?
If your LG washer experienced a power failure, restart the cycle.
What does 'Water Inlet Error' mean on my LG WM2016CW Washer by LG?
A 'Water Inlet Error' on your LG Washer means the correct water level was not reached within 8 minutes after water was supplied, or it did not reach the preset water level within 25 minutes.
What does LOCKED MOTOR ERROR mean on my LG WM2016CW Washer?
A LOCKED MOTOR ERROR can occur for several reasons: the connector (3-pin, male, white) in the MOTOR HARNESS is not connected to the connector (3-pin, female, white) of STATOR ASSEMBLY; the electric contact between the connectors (3-pin, male, white) in the MOTOR HARNESS and 4-pin, female, white connector in the MAIN PWB ASSEMBLY is bad or unstable; the MOTOR HARNESS between the STATOR ASSEMBLY and MAIN PWB ASSEMBLY is cut (open circuited); or the hall sensor is out of order/defective.
Why won't my LG Washer start or spin?
If your LG Washer isn't starting or spinning, ensure the plug is securely in the wall outlet. Check the circuit breaker or fuse, replacing if necessary, but do not increase the fuse capacity. If a circuit overload is the issue, consult a qualified electrician. Also, make sure the water supply tap is on, the door is fully closed, and you've pressed the Start/Pause button. Remember that it may take a moment for the washer to begin spinning after pressing Start/Pause, as the door must lock first.
What to do if my LG Washer has water leaks or excessive suds?
If you notice water leaks or excessive suds in your LG washer, check and tighten all hose connections first. If the issue persists, unclog the drain pipe, contacting a plumber if necessary. To address excessive suds, reduce the amount of detergent you're using or switch to an HE (High Efficiency) detergent.
Why is water not entering or draining properly in my LG Washer?
If water isn't entering your LG washer or is draining slowly, start by checking another tap in your house to ensure adequate water supply. Fully open the tap connected to the washer. Straighten any kinks in the hose. Inspect the filter of the inlet hose for clogs. Additionally, clean and straighten the drain hose, and clean the drain filter to ensure proper drainage.
What does 'EEPROM Error' mean on my LG Washer?
An 'EEPROM Error' on your LG Washer means the EEPROM is out of order. This error is only displayed when the START/PAUSE button is first pressed in the Load Test Mode.
What to do if I get a 'Door Open Error' on my LG WM2016CW?
If you're getting a 'Door Open Error' on your LG Washer, it could be due to a few reasons. First, make sure the door is completely closed. If it is, check for loose electrical connections at the door switch and PWB assembly. If those seem fine, the door switch assembly itself might be faulty and out of order.
What to do if my LG WM2016CW overfills with water?
If the water overfills in your LG washer due to a faulty water valve, close the water tap, unplug the power plug, and call for service.
What does 'Over Flow Error' mean on my LG WM2016CW Washer?
An 'Over Flow Error' on your LG Washer indicates that the water is overflowing, meaning the water level frequency is over 213. If this error is displayed, the drain pump will automatically activate to drain the water.
General| Type | Front Load Washer |
|---|---|
| Width | 27 inches |
| Steam Washer | No |
| Color | White |
| Energy Star Certified | Yes |
| Delay Start | Yes |
| Child Lock | Yes |
| Wi-Fi Enabled | No |
| Depth | 29.75 inches |
| Height | 38.75 inches |
Describes the advanced DC motor driving the drum directly without belt and pulley.
Highlights the tilted drum and large opening for easier loading and unloading.
Explains how the washer automatically detects load and optimizes wash time.
Details the feature preventing children from changing settings during operation.
Describes the display showing settings, time, options, and status messages.
Emphasizes reading all instructions before operating the appliance to minimize risks.
Lists crucial precautions to reduce risks of fire, electric shock, or injury.
Explains the necessity and procedure for grounding the appliance to prevent electric shock.
Lists and illustrates included accessories for the washing machine.
Explains the purpose of shipping bolts and the need for their removal before use.
Provides step-by-step instructions on how to remove shipping bolts using the supplied wrench.
Specifies required space around the washer for proper installation and door opening.
Shows detailed measurements of the washing machine from different views.
Details minimum spacing requirements for recessed area installation.
Stresses the importance of a solid, level floor and provides guidance on floor requirements.
Specifies requirements for the power outlet location and type.
Details electrical connection safety and requirements, including grounding.
Guides on connecting the water supply hose, including pressure and connection points.
Provides instructions and diagrams for correctly installing the drain hose.
Explains how to adjust the leveling feet for stability and to minimize noise and vibration.
Advises checking fabric care labels for washing instructions.
Guides on sorting clothes by color, soil level, and fabric type for best results.
Provides tips for checking pockets, closing zippers, and pretreating stains before loading.
Explains the use of High Efficiency (HE) detergent recommended for the washer.
Details how to add detergent for the main wash cycle.
Guides on adding liquid chlorine bleach to the appropriate compartment.
Explains how to add fabric softener, including dilution and fill lines.
Explains how to turn the washing machine on and off.
Describes how to select different wash cycles using the cycle selector knob.
Details how to start, stop, or pause the washing cycle.
Explains the function to delay the start of a wash cycle for up to 12 hours.
Describes the option to add extra water for improved wash and rinse results.
Explains the SPINSENSE™ function for reducing vibration, especially on uneven floors.
Details the option for an additional rinse cycle to remove detergent residue.
Guides on selecting water temperature based on fabric type and soil level.
Explains how to change the spin speed and how to initiate a drain/spin cycle.
Describes how to adjust the soil level setting for the wash cycle.
Explains how to adjust the volume of the machine's beep alerts.
Explains the different indicators and information shown on the LED display.
Details various cycle options like Prewash, Rinse+Spin, Quick Cycle, Stain Cycle, and Tub Clean.
Explains how the display shows the estimated time for the current cycle or error codes.
Describes the lights that indicate the current portion of the wash cycle.
Explains how to activate and deactivate the child lock feature to prevent unintended use.
Describes the indicator light for the locked door and conditions for unlocking.
Instructions for cleaning the water inlet filter to prevent clogging and error messages.
Guidance on cleaning the drain pump filter to remove lint and small objects.
Steps for removing and cleaning the detergent dispenser drawer and inserts.
Advice on cleaning the washing drum to prevent lime scale and rust spots.
Instructions for cleaning the exterior and interior of the washing machine.
Steps to prepare the washer for storage in freezing temperatures to prevent damage.
Outlines the duration of labor and parts warranty for different components.
Explains the process for obtaining in-home service or locating service centers.
Provides contact information for customer assistance and product information.