LG WTG8532WH - Program Specific Cautions

17
NOTE
* For optimizing the washing algorithm, the displayed time may change during washing-increased by a maximum
of 10 minutes (not including spin irregularity correction time) or decrease by a maximum of 4 minutes.
* The Vapour Mode option cannot be used with all cycles.
* Vapour may not be clearly visible during the Vapour Mode cycles.
This is normal. Too much vapour could damage clothing.
* Do not use Va
pour Mode with delicate fabrics such as wool, silk, or easily discolored fabrics.
Agitation strength button
Vapour Mode button
Hot and cold wash laundry button
Water Level button and
Detergent amount indicator
Remaining wash, reservation
time, and error message display
• Laundry progress is indicated here.
• A flashing indicator means that the
process is in operation, an indicator
which is on but not flashing means
it is awaiting that process and
process indicators that are not lit
means that the process
is complete
or was not selected.
• Allows a higher agitation
intensity.
• It is set to Medium intensity
by default (Select is off.)
Select Intensive Wash
by pressing the button.
(Can be set on all courses
except Delicates, Quiet
Wash and Tub Clean.)
• Vapour Mode can be selected
with the Stain Care, Favorite
and Cotton Wash courses.
It increases the wash
temperatu
re to 60Deg C for
a short period of the wash
cycle.
• Vapour Mode is automatically
selected with the Allergy
care course.
Time Delay
(Reservation) button
• Use for laundry
reservation.
• To cancel, press
the power button.
(refer to page 28)
• To select hot water, cold water, or warm water washing.
• Can be changed during operation.
• If hot wash is selected, the wash is done at the temperature that your hot
water tap is set to and rinse will be done with warm water (hot + cold).
• The preset water temperature for Delicates is Cold water only.
(The laundry can be damaged if Hot water is used)
• Warm water (Hot + Cold Wash)is automatically selected on the stain care,
Allergy Care, Smart Rinse and Tub Clean cycles.
• Press to manually select
the Water Level.
• It can be changed during
operatio
n.
• Detergent indicator
suggests the recommended
powdered detergent
amount to add.
• During operation this indicates the
remaining wash time.
• If there is a malfunction, the error
message will be displayed to assist
in troubleshooting the problem.
Wash Status display
* For optimal Vapour cleaning performance, limit laundry loads to 4 kg or less.
* When the Vapour mode option is selected for the Medium Soiled or Favorite Courses,
the water level will not exceed level ‘7’ in order to maintain optimal performance.
* The control panel may differ according to different models.
Wash, Rinse, Spin button Child lock function Program button
Air dry
START/PAUSE button
SmartDiagnosis
TM
Function Display
Power button
•
To change the wash time,
number of rinses, strength
of spin dry.
• Increase the amount of
Rinses to effectively
remove detergent residue.
• Stops any accidental
changes by making the
keypad inoperative.
• Press ‘rinse’ button and
‘spin’ button
simultaneously for 3
seconds to select or
deselect. (refer to p
age 29)
• Selects the Wash
cycle course.
• Select the
appropriate wash
Cycle to suit the
clothes type and
soil level.
• To shorten dry time.
•
Press the Spin button
for 3 seconds
to select, press power
button to deselect.
(refer to page 26)
• Use to start or pause
the washing process.
• After 4 minutes in
pause status, the
washer will
automatically turn
off.
• It marks the place
to put
the phone to
receive the SDS signals
when prompted to by
a Customer Care
Consultant.
• Use to turn the power
on or off.
• Push again and power
goes on or off.
• The power turns off
automatically about
10 seconds after the
wash is finished.
• Do not touch the lid
during Vapour Mode
cycles.
The lid Surface can
become warm..
Allow the lid lock to
release before
opening the door.
• Do
not attempt to
override the lid lock
mechanism or reach
into the washer
during a Vapour
Mode cycle.
WARNING