Lifegard Pro-MAX User Manual

Lifegard Aquatics introduces the Pro-MAX™ UV Sterilizer, featuring a patent-pending,
flow-through design with less restrictive angled inlet and outlet ports requiring less
plumbing. This unique design enables easy installation of new or replacement systems
as it can be positioned in multiple ways to fit any tight space. Available with 3″
housing in 25, 40, 55, 90 and 120 Watt models and 5″ housing in 55, 90 and 120 Watt
sizes. Each Pro-MAX™ features a High Output UV Bulb, Internal Protective Sleeve, and
UL Listed Ballast which counts down the number of days until you need to replace the
bulb. Maximum Operating Pressure 30 PSI.
3″ Amalgam High Output UV 55W, 90W and
120W
5″ Amalgam High Output UV 55W, 90W and
120W
3″ Standard High Output UV 25W and 40W
Part No.
Description
Lamp
Watts
Lamp
Current
UV
Output
Micro
Watts
UVC
µW/cm
Lamp
Life
(Hours)
UV-C
Output
(Watts)
Max Flow
Rate
Max
Water
Flow
Algae &
Bacteria
Max
Aquarium
Size
Max Pond
Size
R450105
3″ Standard High
Output UV 25W
25
1.2A
0.05
50
9000
7.5
1000 GPH
550 GPH
130 Gallons
2400
Gallons
R450106
3″ Standard High
Output UV 40W
40
1.2A
0.125
125
9000
12
2500 GPH
1200 GPH
250 Gallons
4700
Gallons
R450107
3″ Amalgam High
Output UV 55W
55
1.2A
0.15
150
9000
16.5
3600 GPH
2100 GPH
350 Gallons
6000
Gallons
R450108
3″ Amalgam High
Output UV 90W
90
1.2A
0.27
270
9000
28
4600 GPH
2800 GPH
650 Gallons
11000
Gallons
R450109
3″ Amalgam High
Output UV 120W
120
1.2A
0.32
320
9000
37
6000 GPH
4000 GPH
900 Gallons
14500
Gallons
R450110
5″ Amalgam High
Output UV 55W
55
1.2A
0.15
150
9000
16.5
4000 GPH
2100 GPH
350 Gallons
6000
Gallons
R450111
5″ Amalgam High
Output UV 90W
90
1.2A
0.27
270
9000
28
5500 GPH
2800 GPH
650 Gallons
11000
Gallons
R450112
5″ Amalgam High
Output UV 120W
120
1.2A
0.32
320
9000
37
7000 GPH
4000 GPH
900 Gallons
14500
Gallons
When you receive your Pro Max UV Sterilizer open the box and familiarize yourself with the parts breakdown in line drawing at the end of the
instruction booklet.
Setup Instruction:
The UV comes semi-assembled. You need to install the quartz sleeve (#14), the gaskets (#16 and
#19), the bulb (#17) and connect the ballast.
Remove to 2” nuts (#1) holding the inlet/outlet elbows (#23), on the UV clear
cap (#15) and UV end cap (#2) (total 4 individual 2” nuts on the UV). Once the parts
are removed you will see the O-rings (#3). Make sure they're installed properly as seen in the
Figure 1.
Once a year these O-rings (#3, 8, 16, 19 )need year servicing by applying aquatic friendly silicone
lubricant to make sure they don't get brittle or crack.
Figure 1
Pro-MAX™ Ultraviolet Sterilizer
Setup and Instructions

Lifegard Pro-MAX Specifications

General

Category	Laboratory Equipment
Type	Water Purification System
Power Supply	110-240V, 50/60Hz
Output Water Quality	Type I (Ultrapure)
Operating Temperature	40-90°F (4-32°C)
Warranty	1 Year Limited Warranty

Summary

Pro-MAX TM UV Sterilizer Setup and Instructions

Initial Unpacking and Overview

Guidance on receiving the Pro Max UV Sterilizer, opening the box, and familiarizing with components.

UV Cap and Sleeve Assembly

Instructions for installing the UV clear cap, end cap, and quartz sleeve for proper alignment.

Quartz Sleeve and Bulb Installation

Detailed steps for installing the quartz sleeve, bulb, gaskets, and ensuring a proper seal.

Housing and Ballast Connection

Procedure for connecting the UV housing, ballast, and power, including indicator lights.

Service and Maintenance

Annual Servicing and Bulb Replacement

Recommendations for annual servicing, including UV bulb replacement and O-ring/gasket care.

Protective Sleeve Replacement

Guidance on replacing the internal protective/reflective sleeves for optimal UV efficiency.

Replacement Parts

Parts Identification and Cross-Reference

List of Pro Max UV Sterilizer replacement parts with corresponding part numbers and descriptions.