LIGHTWEIGHT MEILENSTEIN - Installing Clincher Tyres; Installing the Cassette

PREPARATORY WORK & ASSEMBLY
21
ENGLISH
Installing clincher tyres
Rim width, outer
(mm)
Approved
tyre sizes
min.-max.
Approved tyre
inflation pressure
max. (bar/psi)
24 0
25-622 8/116
26-622.–.28-622 7/102
29-622.–.32-622 6/87
Rim height (mm) Required valve length (mm)
–48 60
–63 80
–85 100
Risk of accident through damaged wheels.
•Î
Never.use.tubeless.tires.–.the.rim.well.surface.is.not.hermetically.
sealed.and.will.suffer.damage.as.a.result.of.the.immediate.effect.
caused.by.the.tyre.inflation.pressure .
Risk of accident through a bursting tyre.
•Î
Never.use.latex.rubber.inner.tubes.–.they.are.unable.to.withstand.
the.temperature.created.by.braking.and.rolling.resistance
•Î
Never.exceed.the.tyre.inflation.pressure.approved.by.us,.because.
the.tyre.inflation.pressure.will.increase.considerably.as.a.result.of.
the.temperature.created.by.brakes,.rolling.resistance.and.possi-
bly.high.ambient.temperature.-.see.table
Never use tools to get the tyre onto the rim. We recom-
mend using talcum powder to ease the installation procedure.
Only use suitable plastic tyre levers when removing your tyres – do
not use metal tyre levers under any circumstances.
.)
Only.use.high.quality.and.undamaged.clincher.or.foldable.clincher.
tyres.with.suitable.inner.tubes.–.there.is.no.need.to.install.rim.
tape
.)
Observe.the.min /max .inflation.pressure.values.specified.by.the.
manufacturer .

The.lower.the.inflation.pressure.or.tyre.width.the.higher.the.risk.
of.pinch.flat .In.most.cases.it.will.be.the.rim.flange.(
1
).to.suffer.
from.damage .[
E1
]
Installing the cassette

The.rotor.of.the.Lightweight.rear.wheels.can.be.replaced.in.the.
event.of.a.system.change..
(Campagnolo
®
.<–>.SRAM
®
.XDR.<–>.Shimano
®
)
.–see.Rotor replacement,.page.28

If.necessary,.you.can.get.a.suitable.spoke.protector.from.your.
specialist.dealer
.)
Ensure.that.your.cassette.complies.with.the.rotor.type.of.your.
rear.wheel

A.Shimano
®
.11-speed.road.rotor.(
1
).can.have.a.Shimano
®
/SRAM
®
10s.cassette.(
2
).installed
In.this.case.use.a.spacer.(
3
).(t.=1 9.mm) .[
F1
]

A.Campagnolo
®
.C9,.C10,.C11.or.C12.cassette.can.be.installed.on.
the.Campagnolo
®
.rotor.without.a.spacer

A.SRAM®.12s.XDR.cassette.can.be.installed.on.the.SRAM®.XDR.
rotor.without.a.spacer
.)
Follow.the.instructions.of.the.manufacturer.when.installing.your.
cassette
.)
Tighten.the.lock.ring.(
4
).with.tightening.torque.specified.by.the.
manufacturer.–.max. 40 N·m (354 lbf·in) .[
F1
]