Lilytech ZL-7918A User Manual

Code
Function
Range
Note
Factory Default
P0
High temperature warning point
0 ~ 75℃
38.7
P1
Exhaustion temperature up limit
0 ~ 75℃
Start exhausting for cooling
38.2
P2
Exhaustion temperature low limit
0 ~ 75℃
Stop cooling exhausting
38.0
P3
Main temperature up limit
0 ~ 75℃
Main heater stops heating
38.0
P4
Main temperature low limit
0 ~ 75℃
Main heater starts heating
37.9
P5
Aux temperature up limit
0 ~ 75℃
Aux heater stops heating
37.7
P6
Aux temperature low limit
0 ~ 75℃
Aux heater starts heating
37.5
P7
Low temperature warning point
0 ~ 75℃
37.2
P8
High humidity warning point
0 ~ 99%
70
P9
Humidity up limit
0 ~ 99%
Humidify load stops humidifying
60
Pb
Humidity low limit
0 ~ 99%
Humidify load starts humidifying
55
Pc
Exhaustion humidity up limit
0 ~ 99%
Start ventilation for de-humidifying
65
Pd
Exhaustion humidity low limit
0 ~ 99%
Stop de-humidifying ventilation
60
PE
Over wet exhaustion protection
0/1
0: disable; 1: enable
0
PP
Low humidity warning point
0 ~ 99%
50
Set function control parameter
Press【Set】and【▼】simultaneously to enter into function control parameter setting status.
Press【Enter】to select parameter.
SV window displays the selection from “***” + “F1” to “***” + “FF”.
Press【▲】or【▼】to set the value of the parameter (Keeping the key depressed can fast set).
Keeping【Enter】depressed for 2 seconds will exit setting status, the settings will be saved.
The setting status will exit without saving, if there is no key operation for 15 seconds.
Function control parameter code table:
Code
Function
Range
Note
Factory Default
F1
Egg turn period
1 ~ 999 min
90
F2
Egg turn time
0 ~ 999 sec
0: no egg turning function
180
F3
Egg turn times
0 ~ 999 times
0: turn for ever
0
F4
Air exhausting period
1 ~ 999 min
120
F5
Air exhausting time
0 ~ 999 sec
0: no air exhausting
30
F6
Temperature calibration
-9.9 ~ 9.9℃
0.0
F7
Humidity calibration
-20 ~ 20%
0
F8
Illumination period
1 ~ 999 min
90
F9
Illumination time
0 ~ 999 min
0: no illuminating function
0
FF
Incubated days
0 ~ 99 day
Only clear operation
0
Check Incubated Days and Egg Turned Counter
Press【Enter】and【▲】simultaneously, SV window displays〖incubated days, FF〗“days” + “t1” for 2 seconds.
Press【Enter】and【▼】simultaneously, SV window displays egg-turned-counter “times” + “t2” for 2 seconds.
Control and Operation
On/off operation
Keep【Lamp - I/O】depressed for 2 seconds, controller turns on or off.
Illumination operation
Manual on/off: Press【Lamp - I/O】, lamp turns on or off.
Timer on/off: For every〖Illumination period, F8〗, lamp will be on for〖Illumination time, F9〗.
Temperature control
Main heater: When room temperature ≤〖Main temperature low limit, P4〗, the main heater will be on.
When room temperature ≥〖Main temperature up limit, P3〗, the main heater will be off.
Aux. heater: When room temperature ≤〖Aux temperature low limit, P6〗, the aux. heater will be on.
When room temperature ≥〖Aux temperature up limit, P5〗, the aux. heater will be off.
Temperature and humidity control parameter code table:

Lilytech ZL-7918A Specifications

General

Brand	Lilytech
Model	ZL-7918A
Category	Temperature Controller
Language	English