Lincoln 83753 User Manual

Page
Section
- E35
- 71B
Form 402153
DEC - 2006
Specifications
• Spring driven, automatic rewind, with locking ratchet mechanism (eight locking positions per revolution).
• Brass connectors on hose and reel
MODEL 83753 3/8” AIR HOSE REEL
MODEL 83754 1/2” AIR HOSE REEL
Model 83753
• 50 Feet of 3/8” Hose
275172 Hose ©
• Incoming Air Connection: 1/4” NPT
275174 Swivel ©
• Hose Connections: Male 1/4” NPT
• Maximum Pressure: 300 PSI
• Maximum Air Flow: 25 CFM
•
•
Model 83754
• 50 Feet of 1/2” Hose
275173 Hose ©
• Incoming Air Connection: 1/2” NPT
275175 Swivel ©
• Hose Connections: Male 1/2” NPT
• Maximum Pressure: 300 PSI
• Maximum Air Flow: 35 CFM
•
•
Read and understand entire manual before assembling or using hose reel. Failure to follow instructions or warnings could
result in personal injury and/or property damage.
Installing Hose Reel©
Note: Mounting hardware is not included and must be purchased separately. Decide
first where reel will be mounted before purchasing hardware. Different mounting posi-
tions require different types of hardware.
Reel can be mounted on the floor, ceiling, or wall, wherever it is convenient. When
choosing a location, remember that you can only mount reel to a load-bearing struc-
tural member capable of supporting combined weight of reel, hose, and forces caused
by pulling or maneuvering hose. Generally, mounting reel near air compressor is best
since you can connect the two with a shorter, less expensive length of hose. Also, air
compressor controls will be nearby for convenient adjusting.
Once you have located a mounting spot, consult the “Typical Mounting Positions”
chart below and choose the diagram that most closely matches your mounting posi-
tion. If necessary, adjust guide arm position to match diagram.
Safety Rules
DO NOT EXCEED 300 PSI incoming air pressure (from compressor).
2. Wear impact-resistant eye protection that meets ANSI Spec. Z87.1 in work area at all times.
Do not release hose when rewinding. Hold hose end and allow hose to rewind slowly.
Never allow children to use hose reel. Keep children clear of work area at all times.
© Indicates change

Lincoln 83753 Specifications

General

Brand	Lincoln
Model	83753
Category	Cables and connectors
Language	English

Summary

Product Specifications

Model 83753 Air Hose Reel

Details for the 3/8" air hose reel, including hose length, pressure, and airflow specifications.

Model 83754 Air Hose Reel

Details for the 1/2" air hose reel, including hose length, pressure, and airflow specifications.

General Hose Reel Features

Describes automatic rewind, locking ratchet mechanism, and brass connectors for both hose reel models.

Safety and Installation

Critical Safety Precautions

Warnings regarding pressure limits, eye protection, hose handling during rewind, and child safety.

Hose Reel Installation Guide

Instructions for choosing a mounting location, hardware, and utilizing typical mounting positions.

Operation and Maintenance

Adjusting the Guide Arm

Procedure for repositioning the guide arm to optimize hose management during use.

Adjusting the Hose Ball Stop

Instructions on how to set the hose ball stop for a desired length of hose extension.

Operating the Hose Reel

Steps for pulling, locking, and safely retracting the hose onto the reel.

Adjusting Recoil Tension

Method for modifying the spring tension to control the speed of hose rewinding.

Replacing the Hose

Detailed steps for removing an old hose and installing a new hose onto the reel.

Warranty and Contact Information

Lincoln Industrial Standard Warranty

Details the one-year limited warranty for equipment, including coverage and exclusions.

Lincoln Industrial Special Warranties

Outlines extended warranty periods for specific product series, such as injector series and bare reels.

Lincoln Industrial Contact Details

Provides customer service phone numbers, website, and regional contact information.