Lithonia Lighting WST LED User Manual

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
· To reduce the risk of death, personal injury or property damage from re, electric shock, falling parts, cuts/
abrasions, and other hazards please read all warnings and instructions included with and on the xture box and all
xture labels.
· Before installing, servicing, or performing routine maintenance upon this equipment, follow these general
precautions.
· Installation and service of luminaires should be performed by a qualied licensed electrician.
· Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and
operation and any hazards involved. Regular xture maintenance programs are recommended.
· It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on
ambient dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a
solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry.
Should optical assembly become dirty on the inside, wipe refractor/lens and clean in above manner, replacing
damaged gaskets as necessary.
· DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have
been damaged during transit. Inspect to conrm. Any part damaged or broken during or after assembly should be
replaced.
· Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
· These instructions do not purport to cover all details or variations in equipment nor to provide every possible
contingency to meet in connection with installation, operation, or maintenance. Should further information be
desired or should particular problems arise which are not covered suciently for the purchaser’s or owner’s
purposes, this matter should be referred to Acuity Brands Lighting, Inc.
Disconnect or turn o power before installation or
servicing.
Verify that supply voltage is correct by comparing it with
the luminaire label information.
Make all electrical and grounded connections in
accordance with the National Electrical Code (NEC) and
any applicable local code requirements.
All wiring connections should be capped with UL approved
recognized wire connectors.
WARNING
RISK OF ELECTRIC SHOCK
Allow lamp/xture to cool before handling. Do not touch
enclosure or light source.
Do not exceed maximum wattage marked on luminaire
label.
Follow all manufacturer’s warnings, recommendations
and restrictions for: driver type, burning position,
mounting locations/methods, replacement and recycling.
WARNING
RISK OF BURN
CAUTION
RISK OF FIRE
Keep combustible and other materials that can burn,
away from lamp/lens.
Do not operate in close proximity to persons, combustible
materials or substances aected by heat or drying.
CAUTION
RISK OF INJURY
Wear gloves and safety glasses at all times when removing
luminaire from carton, installing, servicing or performing
maintenance.
Avoid direct eye exposure to the light source while it is on.

Lithonia Lighting WST LED Specifications

General

Manufacturer	Lithonia Lighting
Category	Lighting Equipment
Model	WST LED
Voltage	120-277V
Light Source	LED
CRI	80
IP Rating	IP65
Mounting	Wall
Listings	DLC
Color Temperature	3000K, 4000K
Material	Aluminum

Summary

General Safety Instructions

Risk of Electric Shock

Disconnect power before installation/servicing. Verify voltage and make proper connections.

Risk of Burn

Allow fixture to cool before handling. Do not touch enclosure or light source. Respect wattage limits.

Risk of Injury

Wear safety gear during installation/servicing. Avoid direct eye exposure to the light source.

Risk of Fire

Keep combustible materials away from lamp/lens. Avoid close proximity to heat-sensitive materials.

Product Damage and Installation Precautions

Risk of Product Damage

Avoid connecting components under load, improper mounting, and restricting ventilation.

Electrical and ESD Precautions

Ensure proper polarity, use grounding equipment, and avoid touching components to prevent ESD.

Premium Backbox (PBBW) Installation Details

Delivery, Inspection, and FCC Compliance

Inspect for damage upon receipt. Ensure compliance with FCC Rules for device operation.

Wet Location and Caulking Warning

Backbox is for wet locations only. Apply continuous caulking for weather-tight integrity.

Backbox Plate Removal and Reinstallation

Instructions for safely removing and reinstalling the backbox plate, preserving gasket.

Backbox Mounting and Remote Battery Wiring

Mounting the Premium Backbox

Install backbox to wall using specified screws, ensuring it is level.

Remote Battery Pack Installation and Wiring

Steps for installing remote battery units and routing flex conduit into the backbox.

Final Luminaire Attachment and Wiring

Completing Luminaire Attachment and Wiring

Reattach luminaire to backbox, connect input leads, and push wiring back through the plate.

Remote Battery Pack Activation and Charging

Connect battery pack wires and supply AC power within 90 minutes; allow 24 hours for charging.

Wiring Diagrams and NPT Entry Handling

E23WHR Wiring Diagram

Detailed wiring diagram for the E23WHR option, showing connections from flex conduit.

Handling Unused NPT Entries and Final Assembly

Seal unused NPT entries with plugs and sealant. Refer to IM-401 for fixture-to-backbox mounting.