Little Giant PES Series User Manual

12 pages

To Next Page

PES Series Magnetic Drive Pumps

OWNER'S MANUAL

English

Designed to operate continuously with minimal energy con-

sumption, magnetic drive pumps offer a corrosion-resistant

body specifically for submersible use. Easy to install and

maintain, magnetic drive pumps are ideal for a variety of

applications.

This product is covered by a Limited Warranty for a period of

3 years from the date of original purchase by the consumer.

For complete warranty information, refer to

www.LittleGiant.com

Specifications

SAFETY INSTRUCTIONS

This equipment should be installed and serviced by technically qualified personnel who are familiar with

the correct selection and use of appropriate tools, equipment, and procedures. Failure to comply with

national and local electrical and plumbing codes and within Little Giant recommendations may result in

electrical shock or fire hazard, unsatisfactory performance, or equipment failure.

Know the product’s application, limitations, and potential hazards. Read and follow instructions carefully to

avoid injury and property damage. Do not disassemble or repair unit unless described in this manual.

Failure to follow installation or operation procedures and all applicable codes may result in the following

hazards:

Model Item No. Volts HZ Amps Watts

Discharge Barb

in (cm)

Shut Off

ft (m)

PES-40-PW 566713

120 60

0.03 2.5

1/2, 3/8

(1.27, 0.95)

2.10 (0.6)

PES-80-PW 566714 0.14 8 3.50 (1.1)

PES-130-PW 566716 0.23 11

1/2, 5/8

(1.27, 1.59)

5.50 (1.7)

PES-290-PW 566717 0.4 23 7.25 (2.2)

PES-380-PW 566718 0.64 33 7.00 (2.1)

PES-700-PW 566720 0.75 57

3/4 (1.91)

8.25 (2.5)

PES-800-PW 566721 0.95 114 11.75 (3.6)

PES-1000-PW 566722 1.4 160 1 (2.54) 11.75 (3.6)

Risk of death, personal injury, or property damage due to explosion,

fire, or electric shock.

• Do not use to pump flammable, combustible, or explosive fluids such as gasoline, fuel oil, kerosene, etc.

• Do not use in explosive atmospheres or hazardous locations as classified by the NEC, ANSI/NFPA70.

• Do not handle a pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.

• When a pump is in its application, do not touch the motor, pipes, or water until the unit is unplugged or electri-

cally disconnected.

Other manuals for Little Giant PES Series

Instruction Sheet8 pages

Manual8 pages

Questions and Answers:

J
Jeffrey RobbinsJul 28, 2025
What to do if there is no water flow from Little Giant Water Pump?
- K
  kcarrJul 28, 2025
  If your Little Giant Water Pump isn't pumping water, first, make sure it's properly connected to a power source. Next, ensure the pump's inlet is submerged below the water surface to prime it. If the pump trips the circuit breaker or GFCI, consider replacing the pump.
S
Steven HouseAug 11, 2025
Why is there low water flow from my Little Giant Water Pump?
- A
  aandersonAug 11, 2025
  If your Little Giant Water Pump has low water flow, start by checking the pump intake for any blockages. Remove any debris from the intake screen or impeller. If the pump's capacity is insufficient, consider selecting a larger one. Also, check the flow control valve and adjust it until you reach the desired flow rate.