Loewe Concept 1700 - Recording TV Signals via EURO-AV; Video Recording Copying Function

Recording TV signals with the video
recorder via the EURO-AV sockets.
You will only need this function if your
video recorder cannot receive cable TV
channels or if the TV set is equipped
with a satellite receiver unit. For the
normal TV channels, your video recorder
has its own receiver unit.
We want to show you how to
record a cable TV programme using the
_ video recorder using one practical
example:
® Connect the video recorder with an
AV cable, e.g. to EURO-AV socket 1.
@ On the video recorder, select the
programme provided for external
signals, e.g. “AUX“
@ On the TV set, select the cable
programme which you wish to
record.
® Call up the ‘Main menu*' to the
screen with the button @). Select
“Video recording’ with the blue
arrow button @.
@ Press button @) again.
@ |f “Video recording OFF“ appears
against a yellow background, change
to “Video recording ON" with the
© or © buttons.
® Select the line “AV output’ with the
yellow arrow button @.
@ For our example, set “AV output
EURO 1**,
For “Signal, you can choose
between VTR and SVHS if the set is
equipped with a satellite reception
unit and D2MAC decoder.
@ To store the functions, press button
@ Exit from the menu by pressing the
©) button. The function “Video
recording ON“ prevents you from
accidentally switching to another TV
programme, It is not possible either
to switch off the set to “Standby“
with the remote control unit. If you
try to switch off, the message “Video
recording“ appears against a red
background as a warning.
lf your set is equipped with a
satellite receiver and with “Video
recording ON“, you are recording, for
example, a satellite TV programme, you
can switch to another TV or cable
programme; the satellite will continue to
be transmitted to the video recorder and
can be recorded.
Note:
During two-channel sound and stereo
broadcasts in TV standard PAL, both
sound channels are always output via
the EURO-AV sockets and Cinch
sockets. If, during PAL programmes, you
only wish to record only one of the two
sound channels or to record a stereo
broadcast in mono, press the “Mute“
button @:
Press the “Sound function" button ©
three times; Display: Sound 1+2)) or
Stereo); select Sound 1>) or Sound 2)
for two-channel sound broadcasts or
switch to Mono!)) for stereo broadcasts
with the buttons © @ ©. After making
your selection, switch on the sound for
the loudspeakers again with button @.
Copying of video recordings.
The “Copy“ function allows video
recordings to be copied from one video
recorder to another. The recorders must
both be connected to the EURO-AV
sockets of the television with an AV
cable. It is of no significance whether
the playback recorder is connected to
EURO-AV socket 1 and the recording
recorder to EURO-AV socket 2, or vice
versa - the “copying direction“ is defined
by you in the “Copy“ menu.
Call up the ‘Main menu" with
the button ¢) and select menu line
“Copy“ with the blue arrow button @.
Press button @) again. If the lst line of
the “Copy“ menu shows ‘‘Copy OFF"
and you are receiving a television
programme, this signal is connected to
the EURO-AV sockets.
To start copying, switch to
“Copy ON“ in the “Copy“ menu with
the @ or © buttons.
Move the yellow cursor bar to
“Direction“ with the yellow arrow
button @. You can now determine the
direction of copying with the © or ©
buttons. If you set, e.g. “Direction
EURO-AV 1 > EURO-AV 2% then the
playback video recorder is connected to
EURO-AV socket 1 and the recording
video recorder to EURO-AV socket 2.
Additional “copying directions“ are
shown in the yellow field at the bottom
of the menu, e.g. the possibility of
copying from a camcorder connected to
the front socket “S-term‘ to the EURO-
AV socket 2, etc.
57