Logmaster WLS520-A - Section 2: Safe Operating Instructions; Log Splitter Assembly Guide; Pre-Operation Checks

SECTION
SECTION
SECTION
SECTION 2:
2:
2:
2: Safe
Safe
Safe
Safe Operating
Operating
Operating
Operating Instructions
Instructions
Instructions
Instructions
NOTE: This machine is only intended for homeowners to split firewood as detailed in instructions, not for any
other purpose.
Danger
Danger
Danger
Danger This machine was built to be operated according to the safety instructions in this manual. As with
any type of power equipment, carelessness or error on the part of operator could endanger the personal safety
and/or property of yourself and others. It ca n result in serious injury or death, such as amputating hands or feet,
throwing objects and other unforeseeable damage. Read and follow all instructions before initial operation. The
manufacturer isn ’ t liable for any damages by disregard of the instructions.
1.
1.
1.
1. Assembling
Assembling
Assembling
Assembling your
your
your
your log
log
log
log splitter
splitter
splitter
splitter
•
Cut and remove straps bound to the carton and
unpack the carton.
• Remove the loose parts included with unit (i.e.,
operator ’ s manual, parts assembly, etc.).
• Set the foams aside.
• Connect control handle bars. Pivot each control
handle bar to its linkage part in rear of the splitter
and tighten. ( Fig.
Fig.
Fig.
Fig. 1
1
1
1 )
• Connect the safe guards. Align the holes in the
safe guards with main shield, secure with wrench
and screwdriver. ( Fig.
Fig.
Fig.
Fig. 2
2
2
2 )
NOTE:
a)
Dispose of the packing in an environmental friendly manner. Take to a proper collecting point.
b) If you notice transport damage while unpacking, notify your supplier immediately. Don ’ t operate the
machine.
c)
Read, understand and follow all safety instructions in this manual and labels on the equipment carefully.
d) Keep the manual in a safe place for future and regular reference.
e) Ensure the machine is disconnected from power supply while assembling.
2.
2.
2.
2. Preparation
Preparation
Preparation
Preparation before
before
before
before operating
operating
operating
operating
•
•
•
• Put the machine on the level surface of a sturdy workbench 60
+
cm high.
•
•
•
•
Always block the wheels to prevent movement of the log splitter while in operation.
•
•
•
• Oil the wedge and upper side of the tank, which would make your operating more smoothly.
•
•
•
• Check all nuts, bolts and hydraulic fittings are tight to be sure the equipment is in safe working condition.
•
•
•
•
Make sure your outlet, mains voltage and frequency match the data stated on the model
plate (or “ Technical specifications ” in this manual).
•
•
•
• The power supply for this splitter must have the protection device of under-voltage, over-voltage, circuit
breaker with a residual current device (RCD) which maximum residual current rated at 0.03A.
•
•
•
• Check the switch, power cable and plug are not damaged (no cracks, etc.) to exclude the risk of electric
shock and circuit short.
•
•
•
•
Check all safe shields to be sure they are in the proper position.
•
•
•
• Wear non-slip safety shoes, safety goggles, safety gloves and suitable work clothing. Never wear jewelry,
necktie and other loose clothing.
•
•
•
•
Logs should be cut with square ends and permissible dimensions in advance within the limited capacity .
Uneven log ( e.g. knotted, curved, etc) should not be cut.
Note:
a) Make sure the power cable is unplugged while adjusting.
b)
After adjusting, take away the accessories on or around the unit before switching on.
c) Ensure the motor properly earthed or apply protection device.
d) Use only rubber-jacketed cable of sufficient lead cross section as extension cable. Never use an extension
cord longer than 25 feet. Cord gage must be 14 or lower.
e) Keep away from inflammable liquids or gases before starting the machine.
f) Hydraulic oil is flammable and can explode. Always take a Class B fire extinguisher with you when
operating this log splitter in dry area as a precautionary measure against possible flying sparks.
g) Always check the oil level of the hydraulic reservoir before operation. Operating the log splitter without an
adequate oil supply will cause severe damage to the pump.
h)
Keep handles free of oil, grease and resin.
7
7
7
7
Fig.
Fig.
Fig.
Fig. 1
1
1
1
Fig.
Fig.
Fig.
Fig. 2
2
2
2