EasyManua.ls Logo

Lombardini 4 LD 640 User Manual

Lombardini 4 LD 640
12 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Question and Answer IconNeed help?

Do you have a question about the Lombardini 4 LD 640 and is the answer not in the manual?

Lombardini 4 LD 640 Specifications

General IconGeneral
BrandLombardini
Model4 LD 640
CategoryEngine
LanguageEnglish

Summary

Engine Specifications

Maximum Operating Angles

Details on maximum permissible inclines for engine operation.

Overall Dimensions

Provides external dimensions and measurements of the engine.

Engine Component Identification

Fuel System Identification

Identifies the injection pump, fuel filter, and fuel lines.

Air Intake and Exhaust Systems

Locates the air cleaner and muffler.

Starting and Control Components

Identifies starting mechanisms, throttle lever, and oil level gauge.

Pre-Start Procedures and Fluid Management

Mandatory Pre-Start Instructions

Crucial advice to read and follow instructions before starting to ensure warranty.

Engine Oil Procedures

Covers oil refueling, checking the oil level, and recommended oil type.

Fuel and Air Filter Refueling

Instructions for refueling fuel and adding oil to the air filter.

Engine Operation and Starting

Cold Weather Fuel Preparation

Guidance on mixing fuel with kerosene for cold conditions.

Starting Methods

Covers rope, hand crank, and electric starting procedures.

Engine Operation Controls

Explains throttle position, decompression, and fuel supplement.

Initial Run-in Procedure

Details the recommended procedure for the engine's initial run-in period.

Maintenance Intervals and Procedures

Initial Load Limit

Do not exceed 70% of total load during the first 50 operating hours.

Stopping the Engine

Instructions on how to properly stop the engine using lever or key.

Routine Maintenance Checks

Procedures for checking oil level and cleaning air filter components.

Scheduled Maintenance Intervals

Specifies maintenance tasks to be performed every 8 and 100 hours.

Periodic Maintenance Tasks

Cooling Fins Cleaning

Instructions for cleaning the engine's cooling fins.

Fuel Filter Replacement

Procedure for replacing the fuel filter.

Tightening Delivery Unions

Ensuring proper tightness of fuel delivery unions.

Injector Setting and Cleaning

Guidance on setting and cleaning engine injectors.

Engine Overhaul and Long-Term Storage

Overhaul Procedures

Details on partial and general overhaul at specific hour intervals.

Clutch Adjustment

Procedure for adjusting the clutch play.

Oil and Fuel Filter Replacement

Instructions for replacing oil and fuel filters.

Long-Term Storage Guidelines

Recommendations for storing the engine for extended periods (16 months).

Advanced Maintenance and Lubrication

Oil Filter Replacement

Procedure for replacing the engine oil filter.

Cylinder Lubrication

Guidance on lubricating the engine cylinders.

Storage Recommendations

Instructions for storing the engine for periods exceeding 6 months.

Valve Sealing Procedure

How to close exhaust and intake valves for storage.

Electrical System Diagrams

Fuel System Circuit

Diagram illustrating the fuel lines, pump, and injectors.

Wiring Diagram (Without Warning Light)

Electrical schematic for systems without a battery charging warning light.

Wiring Diagram (With Warning Light)

Electrical schematic for systems with a battery charging warning light.

Troubleshooting Common Issues

Fuel System Problems

Identifies probable causes for fuel system related starting and running issues.

Lubrication System Issues

Troubleshooting steps for lubrication system problems like low oil pressure.

Maintenance and Adjustment Issues

Addresses problems arising from incorrect settings or lack of maintenance.

Electrical System Faults

Diagnosing issues related to the electrical system, battery, and starting motor.

Safety Rules and Starting Accessories

General Safety Precautions

Emphasizes the use of safety guards and proper engine handling.

Use of Original Ropes

Recommends using only genuine LOMBARDINI ropes for starting.

Use of Original Hand Cranks

Recommends using only genuine LOMBARDINI hand cranks for starting.

Service and Parts Information

Ordering Spare Parts

Guidance on how to order replacement parts.

Engine and Machine Identification

Information on identifying engine type, model, and spare part numbers.

Contacting Service Centers

Instructions on how to contact authorized Lombardini service stations.

Related product manuals