To Next PageTo Next PageWhy doesn't the blower run on my Lopi Indoor Fireplace?
The blower on your Lopi Indoor Fireplace may not run because the stove hasn't reached operating temperature yet; it typically starts after 15 to 30 minutes. Also, check the household breaker or fuse to ensure electricity is flowing to the blower.
Why my Lopi Revere Indoor Fireplace does not burn hot enough?
There are several reasons why your Lopi Indoor Fireplace might not be burning hot enough. It could be due to wet wood, which is detailed in the "Selecting Wood" section. Insufficient draft, influenced by chimney height and outside conditions, can also slow the fire. Ensure the air control is fully open and not stuck by sliding it back and forth.
How to stop smoke entering the room during Lopi Indoor Fireplace start-up?
If smoke enters the room during start-up of your Lopi Indoor Fireplace, it could be due to a cold air blockage. Try burning a piece of newspaper to establish a draft. Also ensure the flame is getting enough air by opening the air control. If more air is needed, slightly crack the door.
What to do if smoke enters the room while reloading Lopi Indoor Fireplace?
To prevent smoke from entering the room while reloading your Lopi Indoor Fireplace, stabilize the air before fully opening the door by pulling the air control out. Open the door about an inch and allow air to enter the firebox for a few seconds. Once the smoke consistently flows up the chimney, open the door completely. Insufficient draft, affected by chimney height and outside conditions, may also cause this; adding more pipe or a draft-inducing cap might help.
Why my Lopi Revere kindling does not start and fire smolders?
If the kindling in your Lopi Indoor Fireplace isn't starting and the fire is smoldering, it could be due to a cold air blockage; try burning a piece of newspaper to establish a draft. Also, ensure you're using enough starter paper; add more newspaper if needed. Insufficient air could also be the cause; make sure the air control is open, and if more air is required, crack the door slightly.
Why Lopi Revere does not burn long enough?
Your Lopi Indoor Fireplace may not burn long enough due to several factors. Ensure the doors are sealing properly to prevent air from entering the firebox. Also, check the ash bed for coals; often, glowing coals are under a layer of fly ash. Rake these into a pile to quickly restart the stove. This appliance can burn for up to 8 hours, but burn time may be shorter depending on wood, draft, and other conditions.
General| Maximum Burn Time | Up to 10 Hours |
|---|---|
| Firebox Material | Steel |
| Blower Included | Optional |
| Fuel Type | Wood |
| EPA Certified | Yes |
| Venting | 6-inch diameter |
| Type | Wood Burning Fireplace Insert |
Warns about hot glass causing burns and preventing children from touching.
Guidelines for safe door use, airflow, and fire starters.
Prohibits flammable liquids and specifies approved fuel types.
Emphasizes proper installation, permits, and chimney maintenance.
Covers cooling, over-firing, door seals, and manual handling.
Minimum clearance and dimension requirements for masonry and ZC fireplaces.
Specifies minimum clearances for positioning the insert within the fireplace.
Details chimney liner, condition, and height requirements for masonry installations.
Lists compatible ZC fireplace manufacturers and chimney specifications.
Step-by-step guide for creating and installing a block-off plate.
Steps for verifying installation and curing the paint on the first fires.
Explains CO emissions and the dangers and signs of over-firing the unit.
Instructions and warnings for safely starting a fire in the insert.
How to use the air control slider to manage the burn rate.
Recommended air control positions for different burn levels.
Guidance on loading wood and achieving efficient low burns.
Procedures for safely re-loading the insert and achieving overnight burns.
Advice on wood types, preparation, and burning techniques for efficiency.
Lists materials that should never be burned in the appliance.
Addresses smoke entering the room and draft-related issues.
Solutions for inserts not burning hot, long, or blower not running.
