■ CHARACTERISTICS
1. Time/calendar display: Hour, minute,
seconds, date, day of the week and month.
2. Automatic calendar adjustment: Calendar
adjusts automatically for odd and even months
except February of leap years.
3. Time indication: Changeover between
12-hour and 24-hour indication is possible.
4. Stopwatch: 24 hour stopwatch with 1⁄100
second readout up to 40 minutes and with
1 second readout after the first 40 minutes.
Split time measurement is available.
5. Alarm: The alarm rings at the designated
hour and minute with “beep, beep” for 30
seconds.
6. Hourly time signal: Can be set to ring
every hour on the hour with a single “beep”.
■ DISPLAY AND BUTTON OPERATION
Time signal mark
Day indicator
PM mark
(only in the
12-hour
indication)
Alarm mark
Hour Minute Second
The selection is made in the following order.
Button A : Selection of the display
B
C
A
Time/calendar display Stopwatch display
▲
▲
A
▲
▲
A
A
Time/calendar setting Alarm setting
▲
A
Depress button
“A” for 2 sec.
▲
A
Button B : • Calendar (month, date and day)
display in the time/calendar display.
• Start/Stop in the stopwatch function.
• Selection of the digits to be adjusted
in the alarm setting function and
the time/calendar setting function.
Button C :• Alarm display in the time/calendar
display.
• Split/Split release/Reset in the
stopwatch function.
• Setting the digits in the alarm
setting function and the time/
calendar setting function.
• Stopping the alarm in any display.
Button B while keepig button C depressed:
Engagement and disengagement
of the alarm and the time signal.
Button C while keeping button B depressed:
Changeover of the calendar (month
and date) display.
Buttons B & C:
Alarm test in the time/calendar
display.
■
HOW TO SET THE DUAL CALENDAR
DISPLAY
1. Depress button “B” to show the calendar
(month, date, and day) display. The calendar
display is shown while button “B” is kept
depressed.
2. The month and the date change places
with each other with each depression of
button “C” while keeping button “B” de-
pressed.
Day Month
* “A” (AM) appears in the morning, and “P”
(PM) in the afternoon.
▲
▲
■ HOW TO USE THE STOPWATCH
Split
indicator
Stopwatch
indicator
Stop indicator
1/100 second
indicator
B:
Start/Stop
C:
Split/
Split release/
Reset
1/100 secondSecondMinute
▲
A
1. Depress button “A” to show the stopwatch
display. (The stopwatch indicator starts
flashing.)
The stopwatch can measure up to 24 hours
and is displayed in minutes, seconds, and
1/100 second up to 40 minutes, and in
hours, minutes, and seconds after the first
40 minutes. (The 1/100 indicator flashes
during the first 40 minutes.)
When the measurement is over 24 hours,
the stopwatch will be reset to “0:00oo”
and start counting again.
2. Reset the digits to “0:00oo” before using
the stopwatch. When the split and the
stopwatch indicators are flashing, depress
button “B” to check that the stop indicator
starts flashing, and then depress button
“C” twice to reset the digits to zero.
3. When measuring a long period of time,
return the stopwatch to the time/calendar
display after the stopwatch starts to prevent
any possible mistaken operation.
* When button “B” or “C” is depressed in
the stopwatch display, a single beep” sounds
to confirm the operation.
Accumulated elapsed time measurement
Reset
C
RestartStopStart
BBB B
Accumulate repeatedly by
depressing button “B”.
Stop
Split time measurement
Reset
C
SplitStart
BC C B
Stop
Split
release
Can repeat by depressing
button “C”.
Measurement between two competitors
B BCCC
Finish (Second runner)
Finish (First runner)
ResetSplitStart Stop
Split
release
Month Day Date Date
To Next Page
Need help?
General
