041588
Rev. A
04/2019
PowPak | Installation
Control Module with EcoSystem
Test
Link
Cal.
+
For each system, ensure that you have:
One PowPak Control Module At least one Wireless Transmitter At least one EcoSystem LED Driver or Fluorescent Ballast
Required Components
Radio Powr Savr Occupancy/Vacancy Sensor
(10 maximum)
Radio Powr Savr Daylight Sensor
(1 maximum)
Pico Remote Control
(10 maximum)
64 mA guaranteed for the control lines. May be pre-installed in light fixture.
Note: All drivers and ballasts used with Vive wireless controls must comply with the limits
for a Class A device, pursuant to Part 15 of the FCC rules.
Raise
Toggle
Lower
Top LED
This device can be installed on a junction box or marshalling box using the conduit nut or with mounting
screws and must be installed away from a fixture/troffer. The device must NOT be mounted inside
or on a fixture/troffer or other metallic enclosure. Improper installation can result in degraded wireless
communication, intermittent or sustained communication failures, and will not be covered under
warranty.
For applications where code requires the PowPak fixture control to be installed inside an additional
junction box (e.g., U.S.A.), please see Lutron Application Note #423 (P/N 048423) at www.lutron.com.
+
Occupancy Sensors
Daylight Sensor
Wireless Controls
Occupied: All lights 100%.
Unoccupied: All lights off.
Test
Link
Cal.
All lights dim in response to daylight.
On All lights 100%
Favorite All lights 50%
Off All lights off
Default Functionality
2
A
The PowPak Control Module can be installed on a junction box or
marshalling box using the conduit nut (provided) or with mounting
screws (provided) and must be installed away from a fixture/troffer.
The device must NOT be mounted inside or on a fixture/troffer or other
metallic enclosure. Please consult local and national electric codes for
proper installation.
B
Once installed, energize the PowPak Control Module.
C
Use the Toggle “ u” , Raise “
▲
” and Lower “
Δ
” buttons to verify
control wiring.
English
All Wireless Transmitters must be installed within 30 ft (9 m) of
the PowPak Control Module with EcoSystem technology.
EcoSystem / DALI Control: 18 V-
Guaranteed Supply Current: 64 mA
Maximum Supply Current: 250 mA
120 – 277 V~ 50 / 60 Hz 80 mA
RMJS-ECO32-SZ
A
Connect mains wiring (hot, neutral) to each fixture.
B
Connect EcoSystem control to each fixture.
1
E1
E2
NEU
HOT
EcoSystem
MAINS
To additional EcoSystem fixtures
Neutral
Line/Hot
E1 / DA+
E2 / DA-
+
–
WARNING! Shock Hazard. May result in serious injury or death. Turn off power at circuit
breaker before installing the unit.
Sample LED
driver shown
Important Notes: Please read before installing.
For installation by a qualified electrician in accordance with all local and
national electrical codes.
• Use copper conductors only.
• Check to see that the device type and rating is suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely
before installation.
• Operate between 32 °F and 104 °F (0 °C and 40 °C) ambient.
• 0% to 90% humidity, non-condensing.
• For indoor use only.
Start Here
X
Vive
Programming with a Vive Hub
3
Mount, Wire, and Install EcoSystem
Devices and Lighting Fixtures
Consult third-party device installation guide
Install PowPak Control Module with
EcoSystem technology
Suggested Installation Location: Center of room to
ensure proper RF coverage of area.
A
Use an iOS or Android compatible device.
B
Download the Lutron Vive app.
C
Open the app and follow the instructions.
Note: For further information on set up, programming, and troubleshooting with a Vive
system, please refer to the installation instructions included with the Vive hub or visit
www.lutron.com/vive
Note: For programming the PowPak Control Module with EcoSystem technology
without a Vive hub see reverse side.
Customer Assistance www.lutron.com/support
Troubleshooting www.lutron.com / vive
Ballasts cannot be controlled locally from PowPak Control Module
with EcoSystem technology.
• Ensure that the breaker(s) to the PowPak Control Module are energized.
• Ensure that the EcoSystem control lines are wired to the lighting fixture(s).
Reset to factory defaults.
Lights do not respond to Wireless Transmitter(s).
• Ensure that the breaker(s) to the PowPak Control Module and drivers/ballasts are energized.
• Ensure that Wireless Transmitters are associated to the PowPak Control Module.
• Ensure that Wireless Transmitter(s) are within 30 ft (9 m) of the PowPak Control Module.
Reset to factory defaults.
Lights are unstable at low-end or flash/flicker at turn-on or turn-off. • Adjust the low-end trim.
Wireless Transmitter(s) cannot be associated to PowPak Control
Module with EcoSystem technology.
• Ensure that Wireless Transmitter(s) are within 30 ft (9 m) of the PowPak Control Module.
• The maximum number of Wireless Transmitters have been associated to the PowPak Control Module. To remove a previously set up Wireless Transmitter, tap a
Wireless Transmitter button three times; on the third tap hold for three seconds and then tap three more times.
Part of the Vive Family
vive.lutron.com
X
EcoSystem to Fixtures
E1 / DA+ (Violet)
E2 / DA- (Violet/White)
Neutral (White)
Line / Hot (Black)
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036
041695
Rev. A
04/2019
Bottom
LED
30 ft (9 m)
maximum
Radio Powr
Savr Occupancy
Sensor
Pico
Remote
Control
PowPak
Control Module
Install in center of room
to maximize RF coverage.
PowPak
Control
Module
Wire Gauge Total Digital Link Wire Length
EcoSystem DALI
12 AWG (4.0 mm
2
) 2200 ft (671 m) 984 ft (300 m)*
14 AWG (2.5 mm
2
) 1400 ft (427 m) 984 ft (300 m)*
16 AWG (1.5 mm
2
) 900 ft (275 m) 900 ft (275 m)
18 AWG (1.0 mm
2
) 570 ft (175 m) 570 ft (175 m)
* Maximum recommended length as per IEC 62386-101 Ed. 2.0
To Next Page
Need help?
General
