EasyManua.ls Logo

Lutron Electronics GRAFIK Eye QS - User Manual

Lutron Electronics GRAFIK Eye QS
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
The GRAFIK Eye QS with DALI® control unit allows for control
of both lights and window treatments, without interfaces, using
a single control unit. Features include pushbutton scene recall,
info screen that displays energy savings and status, IR receiver,
astronomic timeclock, contact closure input, and engravable
backlit buttons that are easy to find and operate. The built-in
DALI® bus link can control up to 64 DALI® devices.
Model Numbers: QSGRK-6D, QSGRK-8D, QSGRK-16D
QSGR-6D, QSGR-8D, QSGR-16D
QSGRM-6D, QSGRM-8D, QSGRM-16D
Ratings: 230 V~ 50/60 Hz 100 mA
Output: IEC PELV supply: 24 V- 150 mA
DALI® Link: 18 V- 250 mA
Contents
Features and Functions of the GRAFIK Eye QS with
DALI® Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Wiring the GRAFIK Eye QS with DALI® Control Unit
Overview of Line Voltage/Mains and DALI® Wiring . . . . . . . . . . . . . . . . 3
Line Voltage Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DALI® Bus Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview of IEC PELV Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . 6
QS Link Control Wiring Details . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power Group Wiring Example . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Completing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming Mode
Entering and Exiting Programming Mode . . . . . . . . . . . . . . . . . . . 10
Navigating Menus in Programming Mode . . . . . . . . . . . . . . . . . . . 10
Wireless Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Zone Setup
Assigning Load Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Assigning Non-Dim Load Type . . . . . . . . . . . . . . . . . . . . . . . . 12
Scene Setup
Setting Zone Levels, Fade Rates, and Window Treatment
Group Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DALI® Setup
Building the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Assigning/Unassigning a DALI® Device to a Zone . . . . . . . . . . . . . . . 15
Occupancy Sensor Setup
Associating Wireless Occupancy Sensors . . . . . . . . . . . . . . . . . . . 16
Scene Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Daylight Sensor Setup
Associating Wireless Daylight Sensors . . . . . . . . . . . . . . . . . . . . 18
Zone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Pico Wireless Control Setup
Associating with a GRAFIK Eye QS Wireless Control Unit . . . . . . . . . . . 20
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Wireless Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DALI® Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
For additional features and advanced functions, see the complete installation and
operation guide at www.lutron.com/qs
English DeutschEspañol Français Italiano
Quick Installation and
Operation Guide
Please Read
LUTRON
ѣᮽ
GRAFIK Eye QS with DALI® Control Unit

Table of Contents

Questions and Answers

  • D
    davidknightJul 31, 2025
    Why Lutron Electronics Control Unit does not power up and the circuit breaker is tripping?
    • B
      brian80Jul 31, 2025
      If your Lutron Electronics Control Unit isn't powering up and the circuit breaker keeps tripping, there might be several reasons. First, the circuit breaker might be off; try switching it on. There could also be a miswire, so verify the wiring to the unit and loads. A system short circuit or overload could also be the cause. In the case of a short circuit, find and correct the shorts. If it is system overload, verify that the zone/unit loading is within the specified ratings.
  • H
    Heather AdamsAug 4, 2025
    What to do if QS devices on link are not working in Lutron Electronics Control Unit?
    • M
      Mitchell JamesAug 5, 2025
      If QS devices on the link aren't working with your Lutron Electronics Control Unit, consider these potential solutions: * First, verify the QS link wiring to all devices to ensure there are no miswires or loose connections. * If the wiring is correct, check if the QS device is associated. Place the QS device into programming mode and hold the “Scene 1” button on the GRAFIK Eye QS control unit to associate the two devices. * Also, verify the functionality and programming on the QS devices to ensure they are correctly set up.
  • A
    Alec FrostAug 8, 2025
    What to do if timeclock events do not occur in Lutron Electronics Control Unit?
    • T
      Tabitha GonzalezAug 9, 2025
      If timeclock events are not occurring or sunrise/sunset events are happening at the wrong time with your Lutron Electronics Control Unit, here's what you can check: * First, make sure the timeclock is enabled. * Next, verify that the time and date are set correctly. * Also, ensure that the location (latitude and longitude) of the unit is accurately set. * Finally, consider whether a holiday schedule is in effect, as the normal schedule will resume when the holiday ends.
  • P
    Paul StewartAug 14, 2025
    Why Lutron Electronics Control Unit zone control does not work or yields incorrect results?
    • J
      Johnny CopelandAug 14, 2025
      If your Lutron Electronics Control Unit's zone control isn't working correctly, consider these possible causes. Check for miswires to ensure loads are connected to the correct zones. Also, look for any loose or disconnected wires and connect the zone wires to the loads. Burned-out lamps can also cause issues, so replace any that are bad. Ensure that the zone is assigned to the appropriate load type. Finally, you might need to adjust the High End/Low End values if the dimming limits are set incorrectly.
  • D
    Desiree HolmesAug 18, 2025
    What to do if one or more zones are always “full on” and zone intensity is not adjustable in Lutron Electronics Control Unit?
    • H
      Heather KimAug 18, 2025
      If one or more zones are always “full on” and the zone intensity is not adjustable on your Lutron Electronics Control Unit, there are a couple of things to check. First, ensure that the loads are connected to the correct zones, as a miswire could be the cause. Also, check for a shorted line output. If the wiring is correct and the issue persists, contact Lutron Customer Assistance.
  • Z
    zjenkinsAug 22, 2025
    How to fix Lutron Electronics Control Unit when it does not allow scene change or zone adjustments?
    • J
      John PetersenAug 22, 2025
      If your Lutron Electronics Control Unit does not allow scene changes or zone adjustments, the unit might be in the wrong save mode; try changing to the correct save mode. Alternatively, a QS device in the system may have locked the unit; check the programming and state of QS devices.
  • B
    Brandon BartlettAug 27, 2025
    What to do if integral contact closure input does not work in Lutron Electronics Control Unit?
    • J
      James BoothAug 27, 2025
      If the integral (direct-wired) contact closure input isn't working on your Lutron Electronics Control Unit, first check the wiring on the contact closure input to ensure there are no miswires. Then, verify that the input device is operating properly and sending an input CCI signal. Finally, confirm that the unit is in the correct CCI mode and/or type for your specific application, and change it if necessary.

Summary

Wiring Overview for GRAFIK Eye QS with DALI

Overview of Line Voltage;Mains and DALI Wiring

Details line voltage/mains and DALI® bus wiring connections.

Programming Mode

Zone Setup and Load Types

Assigning Load Types

How to assign load types to DALI® zones.

Scene Setup

Setting Zone Levels, Fade Rates, and Shade Group Actions

How to set scene levels, fade rates, and shade group actions.

DALI System Setup

Building the System

Process to address and find DALI® devices on the system.

Assigning DALI Devices to Zones

Assigning;Unassigning a DALI Device to a Zone

How to assign or unassign DALI® devices to system zones.

Occupancy Sensor Setup

Associating Wireless Occupancy Sensors

Occupancy Sensor Configuration

Daylight Sensor Setup

Associating Wireless Daylight Sensors

Daylight Sensor Configuration

Pico Wireless Control Setup

Associating Pico Wireless Controls

Troubleshooting

Troubleshooting Wireless Functions

Solutions for wireless function issues.

Troubleshooting DALI Functions

Solutions for DALI® function issues.

Lutron Electronics GRAFIK Eye QS Specifications

General IconGeneral
Operating Temperature32°F to 104°F (0°C to 40°C)
TypeLighting Controller
Load Types SupportedIncandescent, Halogen, Magnetic Low Voltage, Electronic Low Voltage, LED
Power Supply100-240VAC, 50/60Hz
Communication ProtocolLutron QS
CompatibilityLutron HomeWorks QS
Number of Zones (Specific)4, 6, or 8
MountingWall mount
Humidity0% to 90% non-condensing
Number of Zones4, 6, or 8

Related product manuals