LOCKING THE KEYPAD
FACTORY SETTINGS
OPEN WINDOW DETECTION
ADVANCED SETTINGS
8. Repeat the previous steps as many times are you wish
to create as many Eco and Comfort periods as you wish to
have in the same day.
9. When the timer programming reaches the end of the
day, 23:30 ashes. Press OK.
10. Day 2 (2=Tuesday) and CP YES appear on the screen.
You can choose to copy the day 1 program to day 2 or not.
11. If you choose to copy the program, press OK. Day 3
(3=Wednesday) and CP YES appear on the screen. Repeat
this step until you reach the last day of the week.
12. If you choose not to copy the program, press «+» or
«-», CP no now ashes on the screen. Press OK to accept
your choice. You will now have to repeat the programming
steps described above.
13. When you have nished programming the last day of
the week, you must save your program. SAVE appears on
the screen. Press OK to save it. You will then automatically
move into Auto mode. (The temperature set point and
program number are displayed on the screen).
Important: If you choose a program that has already pre
-
viously been customized but which you do not want to
modify, press OK to accept. You will automati cally move
into Auto mode (The temperature setpoint and program
number are displayed on the screen)
.
Notes: program ranges are displayed in a graphic at the
bottom of the screen and the time segment ashes. This
enables you to view an entire day’s program.
Use this function to avoid making any changes to the
transmitter settings. To lock the keypad, press «+» and
«-» simultaneously then press OK. The symbol
is
displayed and the keypad is now locked. Repeat the same
procedure to unlock the keypad. The symbol
disap-
pears.
The symbol is visible on the screen and disappears
when you have deactivated this function in the ad-
vanced settings. When the thermostat detects an open
window, the radiator will switch temporarily to Anti
-frost mode and return to its previous operating mode
after the window has been closed.
To reset the thermostat press and hold button "B" for
20 seconds. The indicator light ashes orange and then
turns stable orange before nally going out completely.
Restart your thermostat by pressing button "B". The
indicator light will ash orange rapidly. Your thermos-
tat is now reset.
Your remote control has an installer menu which allows
you to modify various settings to suit your needs.
Press and hold the OK button on the remote control for
10 seconds until the installer menu appears "bL no", the
symbol
appears. Then press the "+ or -" butt ons
to move through the various settings. You can exit the
installer menu at any time by pressing the return but-
ton
, or going down to the "End" setting to exit and
return to the previous mode.
Descriptions of the various settings:
o "bL no":
Fan is installed (certain radiator models), set to " no" by
default. To choose a different setting, press OK, " no" a-
shes, use the "+ or -" buttons to change it to "YES", press
OK again to accept.
o "rF INI":
Pairing menu, press "OK" once, "INI" and the symbol
ash on the screen. Your radiator is currently pai-
ring.
When the screen returns to the previous mode, your
rst radiator has been successfully paired.
o "tP no":
Display the ambient temperature, set to " no" by default.
To choose a different setting, press OK, " no" ashes, use
the "+ or -" to change it to "YES", press OK again to ac-
cept. In this case, the ambient temperature will always
be displayed on the remote control screen with the sym-
bol and you will have to press to display the set point
temperature for 10 seconds.
o "At YES":
Adaptive start time. This function allows you to anti
cipate the starting of your system. You will reach the
setpoint temperature in the room at the desired time.
It is activated when your system changes from eco to
comfort in AUTO mode. It is set to "YES" by default. For
9
EN
To Next Page
Loading...