To Next PageTo Next Page
Need help?Do you have a question about the Mackie Onyx 820i and is the answer not in the manual?
General| Brand | Mackie |
|---|---|
| Model | Onyx 820i |
| Category | Music Mixer |
| Language | English |
Basic setup, zeroing controls, and initial connections.
Guide on setting optimal input gain and output levels for monitoring.
Lists key features of the Onyx 820i mixer, including preamps and EQ.
Explains how to use the manual, including icons and appendix references.
Illustrates a typical setup for a small live performance scenario.
Diagrams showing stereo and individual channel recording configurations.
Illustrates a typical live sound setup for a larger venue.
Diagram for voice-over and post-production audio workflows.
Details on the IEC power connector and the main power switch.
Explains the FireWire interface for digital audio transfer.
Describes XLR and 1/4" main outputs and their level control.
Details on Control Room outputs and the Alt 3-4 stereo mix bus.
Information on the XLR microphone inputs and Onyx mic preamps.
Details on using insert jacks for external processors on channels 1 and 2.
Connecting line-level instruments and sources to mono and stereo channels.
Using aux sends for monitors/effects and aux returns for processed signals.
Connecting tape decks or other sources to playback and record.
Details on the headphone output, including solo monitoring.
Explains controls for mono channels, including Hi-Z and 3-band EQ.
Details controls for hybrid channels, featuring 4-band EQ and line input options.
Explains controls for stereo channels, including FireWire input selection.
How to use the Hi-Z switch for direct guitar connection on channels 1 & 2.
Using the low-cut filter to reduce bass frequencies on channels 1-4.
Details on applying phantom power to condenser microphones.
Using the +4 dB/-10 dB switch for line inputs on channels 3 & 4.
Choosing between analog line or FireWire inputs for channels 7 & 8.
Adjusting input gain and configuring FireWire send pre/post EQ.
Explains the different EQ flavors available for mono, hybrid, and stereo channels.
Details on High EQ, Mid Frequency, Mid EQ Level, and High Mid EQ.
Explains the Low Mid EQ Level and Low EQ controls for tonal shaping.
Setting levels for aux sends 1 and 2 for monitors or effects.
How the pan control affects stereo imaging and subgrouping.
Using the mute switch for signal muting or routing to the Alt 3-4 bus.
Understanding signal presence and overload indicators on channels.
Adjusting channel output levels and using the solo function for auditioning.
Selecting the main mix as the source for control room and headphones.
Choosing Tape, FW 1-2, or Alt 3-4 as monitoring sources.
Routing selected sources to the main mix for playback or performance.
Adjusting the volume for the control room outputs.
Adjusting the headphone output volume.
Understanding the peak meters and the Rude Solo light indicator.
Overall control of aux send 1 and 2 levels before output.
Configuring aux sends to be pre or post channel fader.
Adjusting the overall level of signals returning from aux returns.
Routing Aux Return 2 signal to the Aux 1 send bus.
Sending aux send signals via FireWire outputs 5 and 6.
Status indicator for the mixer's power.
Using the built-in talkback mic for communication.
Controlling talkback volume and routing it to headphones or aux sends.
Controlling the overall stereo output level to main outputs.
Routing the main stereo mix to FireWire outputs 7 and 8.
Tips for diagnosing and resolving common channel, output, and noise problems.
Guidance on power issues and obtaining warranty or non-warranty service.
Details on the 3-pin XLR connector wiring for microphones.
Explains TS (mono) and TRS (stereo/balanced) 1/4" connectors.
Information on RCA connector usage, typically for Hi-Fi stereo.
Using TRS insert jacks for send/receive signals or send-only taps.
Data on Equivalent Input Noise, Output Noise, and Distortion (THD+N).
Specifications for frequency response, input/output levels, and equalization ranges.
Details on FireWire sample rates, buffer sizes, and audio resolution.
Specifications for VU meters, input/output impedance, and power requirements.
Dimensions and weight of the Onyx 820i mixer.
Instructions and required tools for mounting the mixer in a standard 19" rack.
Step-by-step instructions for installing FireWire drivers on Windows Vista.
Instructions for installing FireWire drivers on Windows XP systems.
Advice on selecting appropriate buffer sizes for optimal performance.
Guide to setting up the mixer with Mac OS X Audio MIDI Setup.
How to modify FireWire sends to be post-insert.
How to modify FireWire sends to be post-fader.
How to modify aux sends to be pre-EQ instead of post-EQ.
