Magnetek Flex 12 PRO - User Manual

19 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Flex EM/EX Transmitter

Engineered

Remote Equipment Control

Part Number: 191-00424-0001 R01

April 2019

© 2019 Magnetek Material Handling

Table of Contents

Questions and Answers

A
Amanda OlsonAug 10, 2025
What to do if my Magnetek Flex 12 PRO is not responding to button presses?
- C
  Carol HartmanAug 10, 2025
  If your Magnetek Transmitter doesn't respond when you press a button, it could be due to several reasons. First, check the transmitter battery level. Also, ensure the red emergency stop button is in the raised position before turning on the transmitter. Try repeating the startup procedure by holding the power key at the START position for up to 2.0 seconds and then release. Verify that both the transmitter and receiver have the same RF channel and Receiver Access Code. Finally, make sure you're within 100 meters (300 feet) of the receiver when starting up.
M
Melissa OrtizAug 25, 2025
Why is my Magnetek Flex 12 PRO Transmitter not responding to button presses?
- R
  Raven AliAug 25, 2025
  Your Magnetek Transmitter may not respond to button presses due to several reasons: 1. **Low Battery:** The transmitter battery might be low. Check the battery level. 2. **Emergency Stop:** The emergency stop button could be activated. Ensure it's elevated before starting. 3. **Startup Procedure:** An improper startup could be the cause. Redo the procedure by holding the power key at 'START' for up to 2 seconds, then release. 4. **RF Channel Mismatch:** The transmitter and receiver might be on different channels. Ensure they match. 5. **Access Code Mismatch:** The Receiver Access Code might be different on the transmitter and receiver. Ensure they are the same. 6. **Out of Range:** The system may be out of range. Start the procedure within 100 meters (300 feet) of the receiver.
N
Nancy MarshSep 1, 2025
How to troubleshoot a Magnetek Transmitter that is not responding?
- K
  Kelsey FieldsSep 1, 2025
  To troubleshoot a non-responsive Magnetek Transmitter: * First, check the transmitter's battery level. * Second, ensure the red emergency stop button is elevated before turning on the transmitter. * Third, redo the startup procedure by holding the power key at the 'START' position for up to 2.0 seconds, then release. * Fourth, verify that the transmitter and receiver unit are on the same channel. * Fifth, confirm that the transmitter and receiver unit have the same Receiver Access Code. * Finally, make sure you are within 100 meters (300 feet) of the receiver when starting the procedure.
T
Trevor FernandezNov 15, 2025
What to do if my Magnetek Flex 12 PRO Transmitter has no response when I press a button?
- J
  Jason FergusonNov 15, 2025
  If your Magnetek Transmitter isn't responding when you press a button, there are several potential causes: * The transmitter might have low battery power. Check the transmitter battery level. * The emergency stop button may have been activated before startup. Ensure the red emergency stop button is elevated before turning on the transmitter. * The startup procedure might have been done incorrectly. Redo the startup procedure by holding the power key at the 'START' position for up to 2.0 seconds and then release. * The system RF channel could be incorrect. Verify that the transmitter and receiver unit are on the same channel. * The Receiver Access Code might be incorrect. Ensure that both the transmitter and receiver unit have the same Receiver Access Code. * The system may be ...

Magnetek Flex 12 PRO Specifications

General

Brand	Magnetek
Model	Flex 12 PRO
Category	Transmitter
Language	English

Related product manuals

Magnetek flex 12em

Preview: Magnetek Flex VUE

Magnetek Flex VUE

Magnetek flex 8em

Magnetek flex 4em

Preview: Magnetek flex 4es

Magnetek flex 4es

Magnetek Flex Pro

Magnetek Flex 8 PRO

Preview: Magnetek Flex EX Series

Magnetek Flex EX Series

Preview: Magnetek Telemotive TelePendant

Magnetek Telemotive TelePendant