Makita DCS460 User Manual

39 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

1

WARNING!

Read and understand this Manual. Always follow safety precautions in the Owner’s and Safety Manual.

Improper use can cause serious injury!

The engine exhaust from this product contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Preserve this Manual carefully!

Owner’s and Safety Manual

for Gasoline Chain Saws

DCS460

DCS510

Table of Contents

Other manuals for Makita DCS460

Instruction Manual36 pages

Questions and Answers:

T
Taylor VillaAug 19, 2025
Why is my Makita DCS460 engine not starting or starting with difficulty?
- A
  April SmithAug 20, 2025
  There could be several reasons why your chainsaw engine isn't starting easily. It could be a malfunction in the fuel supply or compression system, or a mechanical issue. Check the ignition spark and fuel tank, and make sure all components are working properly. Also, inspect the wiring for faults or short circuits, and replace any defective components like the plug cap or spark plug. Ensure the choke is in the correct position, and check and clean the carburetor, fuel filter, and fuel line. Replace any defective packing rings and piston rings. Make sure the spark plug is properly sealed. Finally, replace any broken parts in the starter or engine.
L
Leslie AriasAug 21, 2025
What to do if my Makita DCS460 Chainsaw engine does not start?
- J
  Jasmine FitzgeraldAug 22, 2025
  If your Makita Chainsaw engine is not starting or starts with difficulty, it could be due to a malfunction in the fuel supply, compression system, or a mechanical issue. Check for an ignition spark and ensure the fuel tank is full. Inspect the wiring for faults or short circuits, and verify the condition of the spark plug. Make sure the combination switch is not in the Choke position. Also, check for carburetor defects, suction head cleanliness, fuel line integrity, and cylinder base packing ring integrity.
C
Christine BarberAug 23, 2025
Why does my Makita DCS460 engine not start or only with difficulty?
- J
  Jillian PollardAug 25, 2025
  If your Makita Chainsaw engine doesn't start easily, there may be a problem in the fuel supply system, compression system, or a mechanical issue. Check the ignition spark, make sure the fuel tank is full, check that the starter engages properly, and inspect the wiring, plug cap, and spark plug.
T
Taylor KellyAug 26, 2025
Why does my Makita DCS460 engine start, but die immediately?
- Z
  zburtonAug 26, 2025
  The engine might die immediately due to several reasons. Check the idling adjustment, and clean the fuel filter and carburetor. Also, inspect the tank venting and replace the fuel line, cable, or STOP switch if needed. A dirty decompression valve can also cause this issue, so clean it.
A
anthonywilsonAug 27, 2025
What to do if my Makita DCS460 Chainsaw chain does not run?
- J
  John MillerAug 27, 2025
  If the chain on your Makita Chainsaw isn't running, the chain brake might be activated. Try releasing the chain brake.
M
Michael VillarrealAug 29, 2025
Why does my Makita Chainsaw have warm start difficulties?
- A
  Anita ReyesAug 29, 2025
  Warm start difficulties with your Makita Chainsaw may be caused by an incorrect carburetor adjustment. Make sure to adjust the carburetor correctly.
T
travis38Aug 31, 2025
Why is there no chain lubrication on my Makita DCS460 Chainsaw?
- S
  Sarah WagnerAug 31, 2025
  If your Makita Chainsaw isn't lubricating the chain, the oil tank might be empty, so try refilling it. Also, the oil guide groove could be dirty, so clean it. Finally, the oil pump adjusting screw may be incorrectly adjusted, so adjust it properly.
Q
qrodriguezSep 2, 2025
Why does my Makita DCS460 have insufficient power?
- P
  paige15Sep 3, 2025
  Insufficient power in your Makita Chainsaw may be due to a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a blocked exhaust channel in the cylinder, or a clogged spark arrester screen. To resolve this, clean or replace the air filter, adjust the carburetor, and clear any blockages in the muffler, exhaust channel, and spark arrester screen.
M
michelle61Sep 4, 2025
What to do if Makita Chainsaw starts, but dies immediately?
- L
  Leslie SmithSep 4, 2025
  If your Makita Chainsaw starts but dies immediately, the issue might be an incorrect idling adjustment, or a dirty suction head or carburetor. Try adjusting the idling and cleaning the suction head or carburetor.
B
Brandy LewisSep 7, 2025
How to fix no chain lubrication on Makita DCS460?
- A
  aprilcombsSep 7, 2025
  If your Makita Chainsaw has no chain lubrication, it could be due to an empty oil tank, a dirty oil guide groove, or an incorrectly adjusted oil-pump adjusting screw. Refill the oil tank, clean the oil guide groove, and adjust the oil-pump adjusting screw.

Makita DCS460 Specifications

General

Brand	Makita
Model	DCS460
Category	Chainsaw
Language	English

Summary

Safety and Compliance

General Safety Warnings

Crucial safety advice for operating the chainsaw to prevent injury and accidents.

Chain Saw Operator Safety

Essential Operator Safety Precautions

Key safety rules for safe chainsaw operation, including grip and posture.

Additional Safety Guidelines

Further safety advice applicable to all users, covering fatigue and work area.

General Safety and Operator Requirements

Understanding Kickback Dangers

Detailed explanation of kickback forces and the associated risks.

Chain Saw Operation Basics

Engine Starting Sequence

Step-by-step guide for safely starting the chainsaw engine, including cold and warm starts.

Understanding Reactive Forces

Kickback Mechanism and Effects

Detailed explanation of kickback, its causes, and dangers.

Kickback Prevention and Safety Devices

Factors Affecting Kickback Risk

Discusses factors like chain sharpness, depth gauges, and bar nose.

Methods to Avoid Kickback

Comprehensive list of actions to prevent kickback situations.

Reactive Forces: Pushback and Pull-in

Pushback Avoidance Techniques

Explains pushback, its causes, and methods for avoidance.

Pull-in Avoidance Techniques

Describes pull-in, its causes, and methods for prevention.

Felling a Tree Safely

Felling Site Preparation and Escape Routes

Covers clearing the felling site, escape paths, and tree assessment.

Making the Felling Notch and Hinge

Details creating the felling notch and hinge for directional control.

Advanced Felling Techniques

Sectioning and Plunge-Cut Methods

Techniques for felling larger trees, including warnings and safety considerations.

Cutting Techniques: Bucking and Limbing

Safe Bucking Procedures

Guidelines for safely cutting logs into sections.

Safe Limbing Procedures

Safe methods for removing branches from a fallen tree.

Initial Setup and Assembly

Mounting Guide Bar and Saw Chain

Step-by-step instructions for attaching the guide bar and saw chain.

Chain Installation and Adjustment

Fitting the Chain and Guide Bar

Chain Tension and Brake System Checks

Chain Brake Functionality

Explains the inertia chain brake, its functionality, and operation.

Fueling and Fuel Management

Fuel Mixture and Oil Requirements

Information on fuel types, two-stroke oil, and correct mixture ratios.

Fuel and Oil System Care

Refuelling and Chain Lubrication

Engine Starting and Stopping

Safe Engine Starting Procedures

Detailed steps for cold and warm starting the engine safely.

Carburetor Adjustment

Carburetor Adjustment Steps

Saw Chain Maintenance and Sharpening

When and How to Sharpen the Chain

Guidance on when to sharpen the chain and the basic sharpening process.

Proper Sharpening Techniques

Chain Sharpening Tools and Methods

Chain and Sprocket Replacement

Replacing the Saw Chain

Periodic Maintenance Schedule

Service, Troubleshooting, and Guarantee

Service, Spare Parts, and Guarantee

Troubleshooting Common Issues

A guide to diagnosing and resolving common chainsaw problems.

Related product manuals

Preview: Makita DCS4630

Preview: Makita DCS4600S

Makita DCS4600S

Preview: Makita Dolmar DCS460

Makita Dolmar DCS460

Preview: Makita DCS410

Preview: Makita DCS430