How to troubleshoot a Makita Lawn Mower that does not start?
If your Makita Lawn Mower isn't starting, it could be due to a couple of reasons. First, check the battery; if it has under voltage, recharge it, and if recharging isn't effective, replace the battery cartridge. Also, make sure the lock key is properly inserted.
Why won't my Makita DLM431 Lawn Mower start?
Your Makita Lawn Mower might not start because two battery cartridges are not installed—install the charged battery cartridges. Alternatively, the battery might be under voltage, in which case you should recharge it or replace it if recharging doesn't work. Also, ensure the lock key is inserted.
Why does my Makita Lawn Mower motor stop after a short time?
If the motor of your Makita Lawn Mower stops running after a short period, it could be due to a low battery charge. Try recharging the battery cartridge, and if that doesn't work, consider replacing it. Another possible cause is that the cutting height is set too low. In this case, raise the cutting height.
Why isn't my Makita DLM431 motor reaching maximum RPM?
If the motor on your Makita Lawn Mower isn't reaching its maximum RPM, make sure the battery cartridge is installed correctly as described in the manual. If the battery power is dropping, try recharging the battery cartridge. If recharging isn't effective, replace the battery cartridge.
What to do if the cutting tool on my Makita DLM431 Lawn Mower doesn't rotate?
If the cutting tool of your Makita Lawn Mower does not rotate, stop the mower immediately! A possible cause is a foreign object, like a branch, jammed near the blade. Remove the foreign object to resolve this issue.
Why does my Makita Lawn Mower motor stop running after a little use?
If your Makita Lawn Mower motor stops running shortly after starting, there are a couple of potential causes. First, the battery's charge level might be low, so try recharging the battery cartridge, and if that doesn't work, consider replacing it. Alternatively, the cutting height might be set too low, so try raising it.
What to do if my Makita Lawn Mower motor stops running quickly?
If the motor of your Makita Lawn Mower stops running after a short time, the battery's charge level might be low, so recharge or replace the battery. Another possible cause is that the cutting height is too low, so try increasing it.
Why does my Makita Lawn Mower blade not rotate?
If your Makita Lawn Mower blade isn't rotating, stop the mower immediately. A foreign object, like a branch, might be jammed near the blade. Remove any obstructions.
What to do if my Makita DLM431 Lawn Mower is vibrating abnormally?
If you notice abnormal vibration in your Makita Lawn Mower, stop the mower immediately! This could be because the blade is imbalanced, excessively worn, or unevenly worn. Replace the blade to resolve this issue.
What to do if the cutting tool of my Makita DLM431 Lawn Mower does not rotate?
If your Makita Lawn Mower's cutting tool isn't rotating and you've stopped the mower immediately, it might be due to a foreign object, like a branch, jammed near the blade. Remove any obstructions. If the drive system isn't working correctly, seek repair at your local authorized service center.
Disassembly and assembly of the handle and switch lever mechanism.
Steps for disassembling and assembling the DC motor unit.
Procedure for disassembling and assembling the cutting height adjustment components.
Instructions for disassembling and assembling the front and rear wheels.
Procedure for disassembling and assembling connecting rods and shafts.
Disassembly and assembly of the protective shield for Canadian models.
Steps for disassembling and assembling the rear flap assembly.
Schematic showing the electrical connections and components.
Detailed illustration of wire routing and connections within the mower.
General| Cutting Width | 43 cm |
|---|---|
| Cutting Height Range | 20-75 mm |
| Grass Box Capacity | 50 L |
| Power Source | Battery |
| Battery Type | Li-ion |
| Number of Batteries | 2 |
| Mulching | Yes |
| Self-Propelled | No |
| Voltage | 36 V |
| Cutting Height Adjustments | 13 positions |
To Next Page
